AT89C5131A-RDTUM datasheet(159/188 Pages) ATMEL

159 / 188 page

159

4337K–USB–04/08

AT89C5130A/31A-M

Table 25-2.

WDTPRG Register

WDTPRG - Watchdog Timer Out Register (0A7h)

Reset value = XXXX X000

25.2

WDT During Power-down and Idle

In Power-down mode the oscillator stops, which means the WDT also stops. While in Power-

down mode the user does not need to service the WDT. There are 2 methods of exiting Power-

down mode: by a hardware reset or via a level activated external interrupt which is enabled prior

to entering Power-down mode. When Power-down is exited with hardware reset, servicing the

WDT should occur as it normally should whenever the AT89C5130A/31A-M is reset. Exiting

Power-down with an interrupt is significantly different. The interrupt is held low long enough for

the oscillator to stabilize. When the interrupt is brought high, the interrupt is serviced. To prevent

the WDT from resetting the device while the interrupt pin is held low, the WDT is not started until

the interrupt is pulled high. It is suggested that the WDT be reset during the interrupt service

routine.

To ensure that the WDT does not overflow within a few states of exiting of power-down, it is bet-

ter to reset the WDT just before entering power-down.

In the Idle mode, the oscillator continues to run. To prevent the WDT from resetting the

AT89C5130A/31A-M while in Idle mode, the user should always set up a timer that will periodi-

cally exit Idle, service the WDT, and re-enter Idle mode.

Bit

Number

Bit

Mnemonic

Description

Reserved

The value read from this bit is undetermined. Do not try to set this bit.

WDT Time-out select bit 2

WDT Time-out select bit 1

WDT Time-out select bit 0

S2 S1 S0 Selected Time-out

16384x2^(214 - 1) machine cycles, 16.3 ms at FOSC = 12 MHz

16384x2^(215 - 1) machine cycles, 32.7 ms at FOSC = 12 MHz

16384x2^(216 - 1) machine cycles, 65.5 ms at FOSC = 12 MHz

16384x2^(217 - 1) machine cycles, 131 ms at FOSC = 12 MHz

16384x2^(218 - 1) machine cycles, 262 ms at FOSC = 12 MHz

16384x2^(219 - 1) machine cycles, 542 ms at FOSC = 12 MHz

16384x2^(220 - 1) machine cycles, 1.05 s at FOSC = 12 MHz

16384x2^(221 - 1) machine cycles, 2.09 s at FOSC = 12 MHz

16384x2^S machine cycles

AT89C5131A-RDTUM Datasheet(PDF) 159 Page - ATMEL Corporation

AT89C5131A-RDTUM Datasheet(HTML) 159 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL