Page 2 of 3 Issued Date：2008/05/21

Output Current

Input Current

Model

Number

Input

Range

Output

Voltage

Min. load Full Load

Output

(4)

Ripple & Noise No load

Eff

(4)

(%)

Capacitor

(5)

Load max

LED15-24S3P3 18 - 36 VDC

3.3 VDC

0mA

3500mA

75mVp-p

20mA

587mA

86

1000μF

LED15-24S05

18 - 36 VDC

5 VDC

0mA

3000mA

75mVp-p

20mA

753mA

87

1000μF

LED15-24S12

18 - 36 VDC

12 VDC

0mA

1250mA

100mVp-p

15mA

753mA

87

330μF

LED15-24S15

18 - 36 VDC

15 VDC

0mA

1000mA

100mVp-p

15mA

744mA

88

220μF

LED15-48S3P3 36 - 75 VDC

3.3 VDC

0mA

3500mA

75mVp-p

15mA

297mA

85

1000μF

LED15-48S05

36 - 75 VDC

5 VDC

0mA

3000mA

75mVp-p

15mA

377mA

87

1000μF

LED15-48S12

36 - 75 VDC

12 VDC

0mA

1250mA

100mVp-p

10mA

377mA

87

330μF

LED15-48S15

36 - 75 VDC

15 VDC

0mA

1000mA

100mVp-p

10mA

372mA

88

220μF

PRODUCT STANDARD TABLE

Option

Suffix

Negative remote ON/OFF with DIP(Standard)

Negative remote ON/OFF with SMT

-A

Positive remote ON/OFF with DIP

-B

Positive remote ON/OFF with SMT

-C

DIP type without ON/OFF pin

-D

SMT type without ON/OFF pin

-E

DIP type,negative remote ON/OFF without TRIM pin

-F

SMT type,negative remote ON/OFF without TRIM pin

-G

DIP type without ON/OFF&TRIM pin

-H

SMT type without ON/OFF&TRIM pin

-I

DIP type,positive remote ON/OFF without TRIM pin

-J

SMT type,positive remote ON/OFF without TRIM pin

-K

Note

1. BELLCORE TR-NWT-000332. Case 1: 50% Stress, Temperature at 40ºC.

MIL-HDBK-217F Notice2 @Ta=25 ºC, Full load(Ground, Benign, controlled environment)

2. Maximum value at nominal input voltage and full load.

3. Typical value at nominal input voltage and no load.

4. Typical value at nominal input voltage and full load.

5. Test by minimum Vin and constant resistive load.

6. Trimming allows the user to increase or decrease the output voltage set point of the module. This is accomplished by connecting an external resistor

between the TRIM pin and either the +VOUT pin or the -VOUT pin.

7. The ON/OFF control pin voltage is reference to –Vin. The order number please see product standard table.

8. The power module operate in a variety of thermal environments; however, sufficient cooling should be provided to help ensure reliable operation.

9. The LED15 meets EN55022 class A and class B only with external components connected before the input pin to the converter.

10. An external input filter capacitor is required if the module has to meet EN61000-4-4, EN61000-4-5.

The filter capacitor Power Mate suggest: Nippon chemi-con KY series, 220μF/100V, ESR 48mΩ.

1. All dimensions in Inches (mm)

Tolerance: X.XX±0.02 (X.X±0.5)

X.XXX±0.01 (X.XX±0.25)

2. Pin pitch tolerance ±0.01(0.25)

3. Pin dimension tolerance ±0.004 (0.1)

PIN CONNECTION

PIN

LED15 SERIES

1

+ INPUT

2

- INPUT

3

ON/OFF

4

+VOUT

5

TRIM

6

-VOUT

EXTERNAL OUTPUT TRIMMING

Output can be externally trimmed by using

the method shown below.

6

5

TRIM UP

5

4

TRIM DOWN