TSB41BA3DIPFP datasheet(8/59 Pages) TI

8 / 59 page

TSB41BA3D

SLLS959A – DECEMBER 2008 – REVISED MARCH 2009 ............................................................................................................................................... www.ti.com

Table 1. Terminal Functions (continued)

TERMINAL

I/O

DESCRIPTION

PFP

NAME

TYPE

NO.

LCLK_PMC

CMOS

Link clock. Link-provided 98.304-MHz clock signal to synchronize data transfers from link to

the PHY. On hardware reset, this terminal is sampled to determine the power management

control (PMC) mode.

LCLK_PMC

LPS

BMODE

Mode

No LLC (PMC mode)

n/c(1)

lps

Legacy LLC

LCLK_PMC(2)

lps

Beta LLC

In PMC mode, because no LLC is attached, the data lines (D7–D0) are available to indicate

power states. In PMC mode, the following signals are output:

•

D0—port 0 cable-power disable (see Note)

•

D1—port 1 cable-power disable (port in sleep or disabled)

•

D2—port 2 cable-power disable (port in sleep or disabled)

•

D6—All ports cable-power disable (all ports in sleep/disable) logical AND of bits D0–D2

•

D3–D5 and D7 are reserved for future use.

NOTE: The cable-power disable is asserted when the port is either:

•

Hard-disabled (both the disabled and hard-disabled bits are set)

•

Sleep-disabled (both the disabled and sleep_enable bits are set)

•

Disconnected

•

Asleep

•

Connected in DS mode, but nonactive (that is, suspended or disabled)

Otherwise, the cable-power disable output is deasserted (that is, cable power is enabled)

when the port is dc-connected or active. A bus holder is built into this terminal.

LPS

CMOS

Link power status input. This terminal monitors the active/power status of the link-layer

controller (LLC) and controls the state of the PHY-LLC interface. This terminal must be

connected to either the VDD supplying the LLC through an approximately 1-kΩ resistor or to

a pulsed output which is active when the LLC is powered. A pulsed signal must be used

when an isolation barrier exists between the LLC and PHY (see Figure 8).

The LPS input is considered inactive if it is sampled low by the PHY for more than an

LPS_RESET time (~2.6

µs), and is considered active otherwise (that is, asserted steady

high or an oscillating signal with a low time less than 2.6

µs). The LPS input must be high

for at least 22 ns to be observed as high by the PHY.

When the TSB41BA3D detects that the LPS input is inactive, it places the PHY-LLC

interface into a low-power reset state. In the reset state, the CTL (CTL0 and CTL1) and D

(D0 to D7) outputs are held in the logic 0 state and the LREQ input is ignored; however, the

PCLK output remains active. If the LPS input remains low for more than an LPS_DISABLE

time (~26

µs), then the PHY-LLC interface is put into a low-power disabled state in which

the PCLK output is also held inactive.

The LLC state that is communicated in the self-ID packet is considered active only if both

the LPS input is active and the LCtrl register bit is set to 1. The LLC state that is

communicated in the self-ID packet is considered inactive if either the LPS input is inactive

or the LCtrl register bit is cleared to 0.

LREQ

CMOS

LLC request input. The LLC uses this input to initiate a service request to the TSB41BA3D.

A bus holder is built into this terminal.

PCLK

CMOS

PHY clock. Provides a 98.304-MHz clock signal, synchronized with data transfers, to the

LLC when the PHY-link interface is operating in the 1394b mode (BMODE asserted). PCLK

output provides a 49.152-MHz clock signal, synchronized with data transfers, to the LLC

when the PHY-link interface is in legacy 1394a-2000 (BMODE input deasserted).

CMOS

Power-down input. A high on this terminal turns off all internal circuitry. Asserting the PD

input high also activates an internal pulldown on the RESET terminal to force a reset of the

internal control logic.

PINT

CMOS

PHY interrupt. The PHY uses this output to serially transfer status and interrupt information

to the link when PHY-link interface is in the 1394b mode. A bus holder is built into this

terminal.

(1)

Internal pulldown on LCLK_PMC

(2)

LCLK_PMC from LLC normally low during reset

Submit Documentation Feedback

Product Folder Link(s): TSB41BA3D

TSB41BA3DIPFP Datasheet(PDF) 8 Page - Texas Instruments

TSB41BA3DIPFP Datasheet(HTML) 8 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59

Datasheet Download

Link URL