| Electronic Components Datasheet Search |
|
LTC4160EPDC Datasheet(PDF) 20 Page - Linear Technology |
|
|
|||||||||||||||||||||||||||||
LTC4160EPDC Datasheet(HTML) 20 Page - Linear Technology |
|
20 / 32 page ![]() LTC4160/LTC4160-1 20 41601f OPERATION switching regulator is in On-The-Go mode. When a short circuit condition is detected, FAULT will go low-Z. The ENOTG or VBUSGD pins can be used to determine which fault has occurred. If ENOTG or VBUSGD is low when FAULT went low, then a bad battery fault has occurred. If either pin is high, then a short circuit on VBUS has occurred. NTC Thermistor The battery temperature is measured by placing a nega- tive temperature coefficient (NTC) thermistor close to the battery pack. To use this feature connect the NTC thermistor, RNTC, be- tween the NTC pin and ground and a bias resistor, RNOM, from NTCBIAS to NTC. RNOM should be a 1% 200ppm resistor with a value equal to the value of the chosen NTC thermistor at 25°C (R25). The LTC4160/LTC4160-1 will pause charging when the resistance of the NTC thermistor drops to 0.54 times the value of R25 or approximately 54k for a 100k thermis- tor. For a Vishay Curve 1 thermistor, this corresponds to approximately 40°C. If the battery charger is in constant- voltage (float) mode, the safety timer also pauses until the thermistor indicates a return to a valid temperature. As the temperature drops, the resistance of the NTC thermistor rises. The LTC4160/LTC4160-1 are also designed to pause charging when the value of the NTC thermistor increases to 3.25 times the value of R25. For a Vishay Curve 1 100k thermistor, this resistance, 325k, corresponds to approximately 0°C. The hot and cold comparators each have approximately 3°C of hysteresis to prevent oscilla- tion about the trip point. Grounding the NTC pin disables all NTC functionality. Thermal Regulation To prevent thermal damage to the LTC4160/LTC4160-1 or surrounding components, an internal thermal feedback loop will automatically decrease the programmed charge current if the die temperature rises to 105°C. This thermal regulation technique protects the LTC4160/LTC4160-1 from excessive temperature due to high power operation or high ambient thermal conditions, and allows the user to push the limits of the power handling capability with a given circuit board design. The benefit of the LTC4160/ LTC4160-1 thermal regulation loop is that charge current can be set according to actual conditions rather than worst-case conditions for a given application with the assurance that the charger will automatically reduce the current in worst-case conditions. Overvoltage Protection The LTC4160/LTC4160-1 can protect themselves from the inadvertent application of excessive voltage to VBUS with just two external components: an N-channel MOSFET and a 6.2k resistor. The maximum safe overvoltage magnitude will be determined by the choice of the external MOSFET and its associated drain breakdown voltage. The overvoltage protection circuit consists of two pins. The first, OVSENS, is used to measure the externally ap- plied voltage through an external resistor. The second, OVGATE, is an output used to drive the gate pin of the external MOSFET. When OVSENS is below 6V, an inter- nal charge pump will drive OVGATE to approximately 1.88 • OVSENS. This will enhance the N-channel MOSFET and provide a low impedance connection to VBUS which will, in turn, power the LTC4160/LTC4160-1. If OVSENS should rise above 6V due to a fault or the use of an in- correct wall adapter, OVGATE will be pulled to GND. This disables the external MOSFET and protects downstream circuitry. When the voltage drops below 6V again, the external MOSFET will be re-enabled. The charge pump output on OVGATE has limited output drive capability. Care must be taken to avoid leakage on this pin as it may adversely affect operation. See the Applications Information section for resistor power dissipation rating calculations, a table of recommended components, and reverse-voltage protection. Shutdown Mode The USB switching regulator is enabled whenever VBUS is above VUVLO and the LTC4160/LTC4160-1 are not in USB suspend mode. The ideal diode(s) are enabled at all times and cannot be disabled. |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |