| Electronic Components Datasheet Search |
|
TMC22091KHC Datasheet(PDF) 5 Page - Cadeka Microcircuits LLC. |
|
|
|||||||||||||||||||||||||||||
TMC22091KHC Datasheet(HTML) 5 Page - Cadeka Microcircuits LLC. |
|
5 / 60 page ![]() PRODUCT SPECIFICATION TMC22091/TMC22191 5 Microprocessor Interface The microprocessor interface employs a 13 line format. The RESET pin sets all internal state machines to their initialized conditions, disables the analog outputs, sets the internal SRESET bit LOW (reset condition), and places the encoder in a power-down mode. All register and CLUT data are maintained in power-down mode. If the HRESET bit is set HIGH, line 1 field 1 is started when RESET goes HIGH, and SRESET is ignored. If HRESET is LOW, the encoder remains idle after RESET goes HIGH until Control Register bit SRESET is set HIGH, which initiates line 1 field 1. Two address lines are provided and decoded for access to the internal Control Registers and CLUT. Control Registers and CLUT are accessed by loading a desired address through the 8-bit D7-0 port, followed by the desired data read or write for that address. Both the CLUT and the Control Registers are self-indexing, allowing continuous reads or writes to succes- sive addresses. JTAG Test Interface The TMC22x91 includes a standard 4-line JTAG (IEEE Std 1149.1-1990) test interface port, providing access to all digi- tal input/output data pins. This is provided to facilitate com- ponent and board-level testing. Test/Validation Mode The TMC22x91 may be configured to produce standard color bars or a 40 IRE modulated (or unmodulated) video ramp, independent of any pixel or video data input. Color bars are useful as an idle system output signal. The test sig- nals may be used to verify proper operation of the analog video signal chain. TMC22090/TMC22190 Compatibility The TMC22090 and TMC22190 are earlier versions of the TMC22091 and TMC22191, respectively. They lack the fol- lowing features of the newer versions: 1. Selectable Setup (to support NTSC EIA-J video output for Japan) 2. PAL-M format (for South American applications) 3. Extended EH and SL intervals (to support pixel rates above 15 Mpps) 4. Individual D/A power-down (to reduce total dissipation when some outputs are not required) 5. Luminance I/O processing (to reduce flicker in graphics applications) These features are controlled by registers 0E and 0F, and enabled by setting Register OE bit 7 to ONE. If an applica- tion of the TMC22x90 is programmed with this bit set to ZERO (as recommended in the product documentation) then the corresponding TMC22x91 will perform identically. Though the earlier parts continue to be available, it is recom- mended that the newer devices be used in new designs for the additional flexibility. Older designs may be readily converted to the newer versions to take advantage of the added features and lower cost of the later technology. |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |