PIC18F44J10 datasheet(213/368 Pages) MICROCHIP

213 / 368 page

DS39682E-page 211

PIC18F45J10 FAMILY

17.3.2

EUSART SYNCHRONOUS

MASTER RECEPTION

Once Synchronous mode is selected, reception is

enabled by setting either the Single Receive Enable bit,

SREN (RCSTA<5>), or the Continuous Receive

Enable bit, CREN (RCSTA<4>). Data is sampled on the

RX pin on the falling edge of the clock.

If enable bit SREN is set, only a single word is received.

If enable bit CREN is set, the reception is continuous

until CREN is cleared. If both bits are set, then CREN

takes precedence.

To set up a Synchronous Master Reception:

Initialize the SPBRGH:SPBRG registers for the

appropriate baud rate. Set or clear the BRG16

bit, as required, to achieve the desired baud rate.

Enable the synchronous master serial port by

setting bits, SYNC, SPEN and CSRC.

Ensure bits, CREN and SREN, are clear.

If interrupts are desired, set enable bit, RCIE.

If 9-bit reception is desired, set bit, RX9.

If a single reception is required, set bit, SREN.

For continuous reception, set bit, CREN.

Interrupt flag bit, RCIF, will be set when reception

is complete and an interrupt will be generated if

the enable bit, RCIE, was set.

Read the RCSTA register to get the 9th bit (if

enabled) and determine if any error occurred

during reception.

Read the 8-bit received data by reading the

RCREG register.

10. If any error occurred, clear the error by clearing

bit, CREN.

11. If using interrupts, ensure that the GIE and PEIE bits

in the INTCON register (INTCON<7:6>) are set.

FIGURE 17-13:

SYNCHRONOUS RECEPTION (MASTER MODE, SREN)

TABLE 17-8:

REGISTERS ASSOCIATED WITH SYNCHRONOUS MASTER RECEPTION

Name

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Reset

Values

on page

INTCON

GIE/GIEH PEIE/GIEL TMR0IE

INT0IE

RBIE

TMR0IF

INT0IF

RBIF

PIR1

PSPIF(1)

ADIF

RCIF

TXIF

SSP1IF

CCP1IF

TMR2IF

TMR1IF

PIE1

PSPIE(1)

ADIE

RCIE

TXIE

SSP1IE

CCP1IE

TMR2IE

TMR1IE

IPR1

PSPIP(1)

ADIP

RCIP

TXIP

SSP1IP

CCP1IP

TMR2IP

TMR1IP

RCSTA

SPEN

RX9

SREN

CREN

ADDEN

FERR

OERR

RX9D

RCREG

EUSART Receive Register

TXSTA

CSRC

TX9

TXEN

SYNC

SENDB

BRGH

TRMT

TX9D

BAUDCON ABDOVF

RCIDL

—

SCKP

BRG16

—

WUE

ABDEN

SPBRGH

EUSART Baud Rate Generator Register High Byte

SPBRG

EUSART Baud Rate Generator Register Low Byte

Legend:

— = unimplemented, read as ‘0’. Shaded cells are not used for synchronous master reception.

Note 1:

These bits are not implemented on 28-pin devices and should be read as ‘0’.

CREN bit

RC7/RX/DT

RC6/TX/CK pin

Write to

bit SREN

SREN bit

RCIF bit

(Interrupt)

Read

RXREG

Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4

Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4

‘0’

bit 0

bit 1

bit 2

bit 3

bit 4

bit 5

bit 6

bit 7

‘0’

Q1 Q2 Q3 Q4

Note:

Timing diagram demonstrates Sync Master mode with bit SREN = 1 and bit BRGH = 0.

RC6/TX/CK pin

(SCKP = 0)

(SCKP = 1)

PIC18F44J10 Datasheet(PDF) 213 Page - Microchip Technology

PIC18F44J10 Datasheet(HTML) 213 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL