ISL8013A datasheet(5/17 Pages) INTERSIL

5 / 17 page

FN7526.0

November 25, 2009

Absolute Maximum Ratings (Reference to GND)

Thermal Information

VIN, VDD . . . . . . . . . . . . . . -0.3V to 6V (DC) or 7V (20ms)

EN, SYNCH, PG . . . . . . . . . . . . . . . . . .-0.3V to VIN + 0.3V

LX . . . -1.5V (100ns)/-0.3V (DC) to 6.5V (DC) or 7V (20ms)

VFB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 2.8V

Recommended Operating Conditions

VIN Supply Voltage Range . . . . . . . . . . . . . . . . 2.8V to 5.5V

Load Current Range . . . . . . . . . . . . . . . . . . . . . . . 0A to 3A

Ambient Temperature Range . . . . . . . . . . . . -40°C to +85°C

Thermal Resistance (Typical, Notes 4, 5))θJA (°C/W)θJC (°C/W)

16 Ld 4x4 QFN Package . . . . . . .

Junction Temperature Range . . . . . . . . . . -55°C to +125°C

Storage Temperature Range . . . . . . . . . . . -65°C to +150°C

Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . .see link below

http://www.intersil.com/pbfree/Pb-FreeReflow.asp

CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact

product reliability and result in failures not covered by warranty.

NOTES:

4. θJA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach”

features. See Tech Brief TB379.

5. θJC, “case temperature” location is at the center of the exposed metal pad on the package underside.

Electrical Specifications Unless otherwise noted, all parameter limits are established over the recommended

operating conditions and the typical specification are measured at the following conditions

unless otherwise noted: TA = -40°C to +85°C, VIN = 3.6V, EN = VDD. Typical values are at

TA = +25°C. Boldface limits apply over the operating temperature range, -40°C to

+85°C.

PARAMETER

SYMBOL

TEST CONDITIONS

MIN

(Note 7) TYP

MAX

(Note 7)

UNITS

INPUT SUPPLY

VIN Undervoltage Lockout Threshold

VUVLO

Rising, no load

2.6

2.8

Falling, no load

2.15

2.35

Quiescent Supply Current

IVIN

SYNCH = GND, no load at the output

µA

SYNCH = GND, no load at the output

and no switches switching

µA

SYNCH = VDD, FS = 1MHz, no load

at the output

6.5

Shut Down Supply Current

ISD

VIN = 5.5V, EN = low

0.1

µA

OUTPUT REGULATION

Reference Voltage

VREF

0.790

0.8

0.810

VFB Bias Current

IVFB

VFB = 0.75V

0.1

µA

Line Regulation

VIN = VO + 0.5V to 5.5V (minimal

2.8V)

0.2

%/V

Soft-Start Ramp Time Cycle

OVERCURRENT PROTECTION

Current Limit Blanking Time

tOCON

Clock pulses

Overcurrent and Auto Restart

Period

tOCOFF

SS cycle

Switch Current Limit

ILIMIT

(Note 6)

4.0

4.8

5.9

Peak Skip Limit

ISKIP

(Note 6)

1.2

COMPENSATION

Error Amplifier Trans-Conductance

µA/V

Trans-Resistance

0.213

0.25

0.287

ISL8013A

ISL8013A Datasheet(PDF) 5 Page - Intersil Corporation

ISL8013A Datasheet(HTML) 5 Page - Intersil Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

Datasheet Download

Link URL