| Electronic Components Datasheet Search |
|
ST7565P Datasheet(PDF) 43 Page - Sitronix Technology Co., Ltd. |
|
|
|||||||||||||||||||||||||||||
ST7565P Datasheet(HTML) 43 Page - Sitronix Technology Co., Ltd. |
|
43 / 71 page ![]() ST7565P Ver 2.1b 43/71 2009/09/14 Column Address Set This command specifies the column address of the display data RAM shown in Figure 4. The column address is split into two sections (the higher 4 bits and the lower 4 bits) when it is set (fundamentally, set continuously). Each time the display data RAM is accessed, the column address automatically increments (+1), making it possible for the MPU to continuously read from/write to the display data. The column address increment is topped at 83H. This does not change the page address continuously. See the function explanation in “The Column Address Circuit,” for details. E R/W A0 /RD /WR D7 D6 D5 D4 D3 D2 D1 D0 A7 A6 A5 A4 A3 A2 A1 A0 Column address High bits → Low bits → 0 1 0 0 0 0 1 A7 A6 A5 A4 0 0 0 0 0 0 0 0 0 A3 A2 A1 A0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 ↓ 1 0 0 0 0 0 1 0 1 0 0 0 0 0 1 1 0 1 2 ↓ 130 131 Status Read E R/W A0 /RD /WR D7 D6 D5 D4 D3 D2 D1 D0 0 0 1 BUSY ADC ON/OFF RESET 0 0 0 0 BUSY BUSY = 1: it indicates that either processing is occurring internally or a reset condition is in process. BUSY = 0: A new command can be accepted . if the cycle time can be satisfied, there is no need to check for BUSY conditions. ADC This shows the relationship between the column address and the segment driver. 0: Reverse (column address 131-n ↔ SEG n) 1: Normal (column address n ↔ SEG n) (The ADC command switches the polarity.) ON/OFF ON/OFF: indicates the display ON/OFF state. 0: Display ON 1: Display OFF (This display ON/OFF command switches the polarity.) RESET This indicates that the chip is in the process of initialization either because of a /RES signal or because of a reset command. 0: Operating state 1: Reset in progress Display Data Write This command writes 8-bit data to the specified display data RAM address. Since the column address is automatically incremented by “1” after the write, the MPU can write the display data. E R/W A0 /RD /WR D7 D6 D5 D4 D3 D2 D1 D0 1 1 0 Write data |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |