| Electronic Components Datasheet Search |
|
SS6781ACSTB Datasheet(PDF) 16 Page - Silicon Standard Corp. |
|
|
|||||||||||||||||||||||||||||
SS6781ACSTB Datasheet(HTML) 16 Page - Silicon Standard Corp. |
|
16 / 18 page ![]() www.SiliconStandard.com 16 of 18 SS6781A(G) 1/11/2005 Rev.2.10 TABLE 9 The Operating Mode of SS6781A MODE pin Mode Function VCC Test Safety timer period scaled down to 1/32....etc. Floating Normal Normal operation GND AC - ∆V detection disabled The Mode of LED Display and Trickle Charge The SS6781A provides two LED display modes and five-pulsed trickle charge modes. The tri-level inputs, SEL1 and SEL2 pins, as in the TABLE 6 determine the modes of LED display and trickle charge. TABLE 10 Mode of LED Display and Trickle Charge SEL1 SEL2 Trickle Charge Duty LED Display Mode VCC VCC Floating GND N/A 1/32 1/64 Type 1 Type 1 Type 1 Floating VCC Floating GND 1/128 1/256 N/A Type 1 Type 1 Type 2 GND VCC Floating GND 1/32 1/64 1/128 Type 2 Type 2 Type 2 Display the Battery Charging Status The SS6781A provides two open-drain outputs, LED1 and LED2, to indicate the battery charging status. Refer to the table of LED display mode (TABLE 10), depending on the setting of SEL1 and SEL2 pins, the outputs of LED1 and LED2 pins are shown in the following table: TYPE 1 Power ON Fast Charging Charge Completed Fault Conditions LED1 1Hz ON OFF OFF LED2 OFF OFF ON OFF TYPE 2 Power ON Fast Charging Charge Completed Fault Conditions LED1 1Hz ON OFF 4Hz Flashing LED2 1Hz 4Hz Flashing ON OFF Charging Current Control As shown in the typical application circuit, the SS6781A offers an open-drained output pin, ICON pin, to control the charging current flow in fast charge state and switch on to inhibit the charging current flow in fault conditions. When fast charge is completed, the SS6781A enters the trickle charge mode. In trickle charge mode, the ICON pin output switches with predetermined duty cycle. Refer to the table of trickle charge mode (TABLE 6), the duty cycle is determined by the setting of SEL1 and SEL2 pins. The following table summarizes how ICON pin corresponds to various charging states. Power ON Fast Charging Charge Completed Fault Conditions ICON ON OFF See pin 10 & 11 ON Test Mode Fig. 20 shows the timing diagram for externally controlled PEAK, ADJ, VBT, VTS, SEL1 and SEL2 pin voltages of a recommended SS6781A test scheme, utilizing TEST mode function. Output waveforms of LED1, LED2 and ICON of a properly functioning SS6781A are also shown in the figure. |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |