PIC18F4580-ESLASHML datasheet(205/490 Pages) MICROCHIP

205 / 490 page

DS39637D-page 205

PIC18F2480/2580/4480/4580

18.4.3.2

Reception

When the R/W bit of the address byte is clear and an

address match occurs, the R/W bit of the SSPSTAT

the SSPBUF register and the SDA line is held low

(ACK).

When the address byte overflow condition exists, then

the no Acknowledge (ACK) pulse is given. An overflow

condition is defined as either bit, BF (SSPSTAT<0>), is

set, or bit, SSPOV (SSPCON1<6>), is set.

An MSSP interrupt is generated for each data transfer

byte. Flag bit, SSPIF (PIR1<3>), must be cleared in

software. The SSPSTAT register is used to determine

the status of the byte.

If SEN is enabled (SSPCON2<0> = 1), RC3/SCK/SCL

will be held low (clock stretch) following each data

transfer. The clock must be released by setting bit, CKP

(SSPCON<4>).

See

Section 18.4.4

“Clock

Stretching” for more details.

18.4.3.3

Transmission

When the R/W bit of the incoming address byte is set

and an address match occurs, the R/W bit of the

SSPSTAT register is set. The received address is

loaded into the SSPBUF register. The ACK pulse will

be sent on the ninth bit and pin RC3/SCK/SCL is held

low regardless of SEN (see Section 18.4.4 “Clock

Stretching” for more details). By stretching the clock,

the master will be unable to assert another clock pulse

until the slave is done preparing the transmit data. The

transmit data must be loaded into the SSPBUF register

which also loads the SSPSR register. Then, the RC3/

SCK/SCL pin should be enabled by setting bit, CKP

(SSPCON1<4>). The eight data bits are shifted out on

the falling edge of the SCL input. This ensures that the

SDA signal is valid during the SCL high time

(Figure 18-9).

The ACK pulse from the master-receiver is latched on

the rising edge of the ninth SCL input pulse. If the SDA

line is high (not ACK), then the data transfer is

complete. In this case, when the ACK is latched by the

slave, the slave logic is reset and the slave monitors for

another occurrence of the Start bit. If the SDA line was

low (ACK), the next transmit data must be loaded into

the SSPBUF register. Again, pin, RC3/SCK/SCL, must

be enabled by setting bit, CKP.

An MSSP interrupt is generated for each data transfer

byte. The SSPIF bit must be cleared in software and

the SSPSTAT register is used to determine the status

of the byte. The SSPIF bit is set on the falling edge of

the ninth clock pulse.

PIC18F4580-E/ML Datasheet(PDF) 205 Page - Microchip Technology

PIC18F4580-E/ML Datasheet(HTML) 205 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL