PIC18F4580-ESLASHML datasheet(202/490 Pages) MICROCHIP

202 / 490 page

PIC18F2480/2580/4480/4580

DS39637D-page 202

SSPCON1: MSSP CONTROL REGISTER 1 (I2C™ MODE)

R/W-0

WCOL

SSPOV

SSPEN(1)

CKP

SSPM3(2)

SSPM2(2)

SSPM1(2)

SSPM0(2)

bit 7

bit 0

Legend:

R = Readable bit

W = Writable bit

U = Unimplemented bit, read as ‘0’

-n = Value at POR

‘1’ = Bit is set

‘0’ = Bit is cleared

x = Bit is unknown

bit 7

WCOL: Write Collision Detect bit

In Master Transmit mode:

1 = A write to the SSPBUF register was attempted while the I2C conditions were not valid for a

transmission to be started (must be cleared in software)

0 = No collision

In Slave Transmit mode:

1 = The SSPBUF register is written while it is still transmitting the previous word (must be cleared in

software)

0 = No collision

In Receive mode (Master or Slave modes):

This is a “don’t care” bit.

bit 6

SSPOV: Receive Overflow Indicator bit

In Receive mode:

1 = A byte is received while the SSPBUF register is still holding the previous byte (must be cleared in

software)

0 = No overflow

In Transmit mode:

This is a “don’t care” bit in Transmit mode.

bit 5

SSPEN: Master Synchronous Serial Port Enable bit(1)

1 = Enables the serial port and configures the SDA and SCL pins as the serial port pins

0 = Disables serial port and configures these pins as I/O port pins

bit 4

CKP: SCK Release Control bit

In Slave mode:

1 = Releases clock

0 = Holds clock low (clock stretch), used to ensure data setup time

In Master mode:

Unused in this mode.

bit 3-0

SSPM<3:0>: Master Synchronous Serial Port Mode Select bits(2)

1111 = I2C Slave mode, 10-bit address with Start and Stop bit interrupts enabled

1110 = I2C Slave mode, 7-bit address with Start and Stop bit interrupts enabled

1011 = I2C Firmware Controlled Master mode (slave Idle)

1000 = I2C Master mode, clock = FOSC/(4 * (SSPADD + 1))

0111 = I2C Slave mode, 10-bit address

0110 = I2C Slave mode, 7-bit address

Note 1:

When enabled, the SDA and SCL pins must be properly configured as input or output.

Bit combinations not specifically listed here are either reserved or implemented in SPI mode only.

PIC18F4580-E/ML Datasheet(PDF) 202 Page - Microchip Technology

PIC18F4580-E/ML Datasheet(HTML) 202 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL