Electronic Components Datasheet Search
  New Zealand  ▼
ALLDATASHEET.CO.NZ

X  

ADIS16407PCBZ Datasheet(PDF) 13 Page - Analog Devices

Part # ADIS16407PCBZ
Description  Ten Degrees of Freedom Inertial Sensor Platform stabilization and control
PDF  24 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  AD [Analog Devices]
Direct Link  http://www.analog.com
Logo AD - Analog Devices

ADIS16407PCBZ Datasheet(HTML) 13 Page - Analog Devices

Back Button ADIS16407PCBZ Datasheet HTML 9Page - Analog Devices ADIS16407PCBZ Datasheet HTML 10Page - Analog Devices ADIS16407PCBZ Datasheet HTML 11Page - Analog Devices ADIS16407PCBZ Datasheet HTML 12Page - Analog Devices ADIS16407PCBZ Datasheet HTML 13Page - Analog Devices ADIS16407PCBZ Datasheet HTML 14Page - Analog Devices ADIS16407PCBZ Datasheet HTML 15Page - Analog Devices ADIS16407PCBZ Datasheet HTML 16Page - Analog Devices ADIS16407PCBZ Datasheet HTML 17Page - Analog Devices Next Button
Zoom Inzoom in Zoom Outzoom out
 13 / 24 page
background image
ADIS16407
Rev. A | Page 13 of 24
Power Supply
Table 29. Analog Input, Offset Binary Format
Input Voltage
Decimal
Hex
Binary
3.3 V
4095
The SUPPLY_OUT register (Table 26) provides a measurement
of the voltage that is on the VDD pins of the device. Table 27
illustrates the power supply data format.
Table 26. SUPPLY_OUT (Base Address = 0x02), Read Only
0xFFF
xxxx 1111 1111 1111
1 V
1241
0x4D9
xxxx 0100 1101 1001
1.6118 mV
2
0x002
xxxx 0000 0000 0010
805.9 μV
1
0x001
xxxx 0000 0000 0001
0 V
0
Bits
Description
0x000
xxxx 0000 0000 0000
[15]
New data indicator (ND), 1 = new data in register
DEVICE CONFIGURATION
[14]
Error/alarm, 1 = active, see DIAG_STAT for error flags
The control registers in Table 30 provide users with a variety of
configuration options. The SPI provides access to these registers,
one byte at a time, using the bit assignments in Figure 13. Each
register has 16 bits, where Bits[7:0] represent the lower address,
and Bits[15:8] represent the upper address. Figure 16 provides
an example of writing 0x03 to Address 0x3B (SMPL_PRD[15:8]),
using DIN = 0xBB03. This example reduces the sample rate by a
factor of eight (see Table 46).
[13:12]
Not used
[11:0]
Power supply measurement data, binary format,
2.418 mV/LSB, 0 V = 0x000
Table 27. Power Supply Data, Binary Format
Voltage
Decimal
Hex
Binary
+5.25 V
2171
0x87B
xxxx 1000 0111 1011
+5.0 V
2068
0x814
xxxx 1000 0001 0100
+4.75 V
1964
0x7AC
xxxx 0111 1010 1100
1 V
414
SCLK
CS
DIN
DIN = 1011 1011 0000 0011 = 0xBB03, WRITES 0x03 TO ADDRESS 0x3B.
0x19E
xxxx 0001 1001 1110
4.836 mV
2
0x002
xxxx 0000 0000 0010
2.418 mV
1
0x001
xxxx 0000 0000 0001
0 V
0
0x000
xxxx 0000 0000 0000
INPUT ADC CHANNEL
Figure 16. Example SPI Write Sequence
Dual Memory Structure
The AUX_ADC register provides access to the auxiliary ADC
input channel. The ADC is a 12-bit successive approximation
converter that has an input circuit equivalent to the one shown
in Figure 15. The maximum input is 3.3 V. The ESD protection
diodes can handle 10 mA without causing irreversible damage.
The on resistance (R1) of the switch has a typical value of 100 Ω.
The sampling capacitor, C2, has a typical value of 16 pF.
Writing configuration data to a control register updates its SRAM
contents, which are volatile. After optimizing each relevant control
register setting in a system, set GLOB_CMD[3] = 1 (DIN =
0xBE08) to backup these settings in nonvolatile flash memory.
The flash backup process requires a valid power supply level for
the entire 75 ms process time. Table 30 provides a user register
memory map that includes a flash backup column. A “yes” in this
column indicates that a register has a mirror location in flash and,
when backed up properly, it automatically restores itself during
startup or after a reset. Figure 17 provides a diagram of the dual
memory structure used to manage operation and store critical user
settings.
C2
C1
R1
VCC
D
D
Figure 15. Equivalent Analog Input Circuit
(Conversion Phase: Switch Open,
Track Phase: Switch Closed)
Table 28. AUX_ADC (Base Address = 0x1C), Read Only
NONVOLATILE
FLASH MEMORY
(NO SPI ACCESS)
MANUAL
FLASH
BACKUP
START-UP
RESET
VOLATILE
SRAM
SPI ACCESS
Bits
Description
[15]
New data indicator (ND), 1 = new data in register
[14]
Error/alarm, 1 = active, see DIAG_STAT for error flags
[13:12]
Not used
[11:0]
Analog input channel data, binary format,
0.8059 mV/LSB, 0 V = 0x000
Figure 17. SRAM and Flash Memory Diagram



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com