| Electronic Components Datasheet Search |
|
HT46R92 Datasheet(PDF) 18 Page - Holtek Semiconductor Inc |
|
|
|||||||||||||||||||||||||||||
HT46R92 Datasheet(HTML) 18 Page - Holtek Semiconductor Inc |
|
18 / 61 page ![]() HT46R92 Rev. 1.10 18 November 5, 2008 LCD Driver Function The device contains circuitry to control an external LCD. This function is controlled using the LCDC register. LCD Driver Operation When the LCDEN bit in the LCDC register is set high and PB is configured as an output, ports PB, PC, PD and PE become CMOS outputs, but have lower sink/source capabilities making them suitable for LCD segment driving. Following a power-on reset, port PB will be setup as an input port, while PC is setup as a PMOS output port while PD and PE are setup as NMOS output ports, making them suitable for LED driving. However at this time, as the LCDEN bit is low, the PC, PD and PE outputs will be in an open-drain high-impedance condition. To setup ports PB~PE as CMOS outputs, the LCDEN bit must be set high. It is im- portant to note that PB and PC have a lower sink ability (IOL2) while PD and PE have a lower driving ability (IOH3). The D.C. Characteristics provide for further infor- mation. 1/2 Bias LCD Control As the device may be conveniently used for driving LCD panels, pins PC4~PC7 and other I/O ports can be used together to implement 1/2 bias LCD timing signals. COM0~3 can be sourced from the PC4~7 pins while the SEGMENTS can be sourced from other I/O ports. The internal 1/2 bias circuit is enabled via a combination of the LCDEN and COM0EN~COM3EN bits in the LCDC register. The RSEL bit in the LCDC register selects the bias circuit resistor values which should be chosen ac- cording to the actual LCD panel used and to minimise current consumption. Note that there is only one bias circuit which is shared by all the COM outputs. LCDC Register 1/2 Bias On/Off LCDEN COM3EN COM2EN COM1EN COM0EN 0 xxxx Off 10000 Off 10001 On : : : : : : : : : : ON 11111 ON 1/2 Bias Circuit Control The following steps can be used to implement LCD timing: · Select the bias resistor by setting RSEL=0 or 1 · Set LCDEN=1 · Use software to generate the VDD, VSS, VDD/2 volt- ages by changing COM pins PC4~7 to output high, output low and input respectively. · Generate the segment timing using other I/O ports with outputs equal to either VSS or VDD T 1 T 2 T 3 T 4 T 1 T 2 T 3 T 4 W r i t e t o P o r t R e a d f r o m P o r t S y s t e m C l o c k P o r t D a t a Read/Write Timing L C D C R e g i s t e r 1 / 2 B i a s C O M 0 o u t p u t e n a b l e 1 : e n a b l e 0 : d i s a b l e 1 / 2 B i a s C O M 1 o u t p u t e n a b l e 1 : e n a b l e 0 : d i s a b l e 1 / 2 B i a s C O M 2 o u t p u t e n a b l e 1 : e n a b l e 0 : d i s a b l e 1 / 2 B i a s C O M 3 o u t p u t e n a b l e 1 : e n a b l e 0 : d i s a b l e L C D e n a b l e / d i s a b l e C o n t r o l 1 : e n a b l e 0 : d i s a b l e S e l e c t r e s i s t o r f o r R t y p e L C D b i a s c u r r e n t 1 : 2 x 5 0 k W ( 1 / 2 b i a s ) , I B I A S = 5 0 m A a t V D D = 5 V 0 : 2 x 1 0 0 k W ( 1 / 2 b i a s ) , I B I A S = 2 5 m A a t V D D = 5 V N o t i m p l e m e n t e d , r e a d a s " 0 " b 0 C O M 0 E N b 7 R S E L C O M 1 E N C O M 2 E N C O M 3 E N L C D E N LCD Control Register |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |