VS-16TTS..FPPBF datasheet(2/7 Pages) VISHAY

2 / 7 page

VS-16TTS..FPPbF Series, VS-16TTS...FP-M3 Series

www.vishay.com

Vishay Semiconductors

Revision: 10-Nov-11

Document Number: 94381

For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

ABSOLUTE MAXIMUM RATINGS

PARAMETER

SYMBOL

TEST CONDITIONS

VALUES

UNITS

TYP.

MAX.

Maximum average on-state current

IT(AV)

TC = 95 °C, 180° conduction, half sine wave

Maximum RMS on-state current

IRMS

Maximum peak, one-cycle,

non-repetitive surge current

ITSM

10 ms sine pulse, rated VRRM applied

170

10 ms sine pulse, no voltage reapplied

200

Maximum I2t for fusing

I2t

10 ms sine pulse, rated VRRM applied

144

A2s

10 ms sine pulse, no voltage reapplied

200

Maximum I2

t for fusing

t

t = 0.1 to 10 ms, no voltage reapplied

2000

s

Maximum on-state voltage drop

VTM

10 A, TJ = 25 °C

1.4

On-state slope resistance

TJ = 125 °C

24.0



Threshold voltage

VT(TO)

1.1

Maximum reverse and direct leakage current

IRM/IDM

TJ = 25 °C

VR = Rated VRRM/VDRM

0.5

TJ = 125 °C

Holding current

Anode supply = 6 V, resistive load, initial IT = 1 A

16TTS08FP, 16TTS12FP

100

Maximum latching current

Anode supply = 6 V, resistive load

200

Maximum rate of rise of off-state voltage

dV/dt

500

V/μs

Maximum rate of rise of turned-on current

dI/dt

150

A/μs

TRIGGERING

PARAMETER

SYMBOL

TEST CONDITIONS

VALUES

UNITS

Maximum peak gate power

PGM

8.0

Maximum average gate power

PG(AV)

2.0

Maximum peak positive gate current

+ IGM

1.5

Maximum peak negative gate voltage

- VGM

Maximum required DC gate current to trigger

IGT

Anode supply = 6 V, resistive load, TJ = - 10 °C

Anode supply = 6 V, resistive load, TJ = 25 °C

Anode supply = 6 V, resistive load, TJ = 125 °C

Maximum required DC gate

voltage to trigger

VGT

Anode supply = 6 V, resistive load, TJ = - 10 °C

3.0

Anode supply = 6 V, resistive load, TJ = 25 °C

2.0

Anode supply = 6 V, resistive load, TJ = 125 °C

1.0

Maximum DC gate voltage not to trigger

VGD

TJ = 125 °C, VDRM = Rated value

0.2

Maximum DC gate current not to trigger

IGD

2.0

SWITCHING

PARAMETER

SYMBOL

TEST CONDITIONS

VALUES

UNITS

Typical turn-on time

tgt

TJ = 25 °C

0.9

μs

Typical reverse recovery time

trr

TJ = 125 °C

Typical turn-off time

110

VS-16TTS..FPPBF Datasheet(PDF) 2 Page - Vishay Siliconix

VS-16TTS..FPPBF Datasheet(HTML) 2 Page - Vishay Siliconix

Html Pages

1 2 3 4 5 6 7

Datasheet Download

Link URL