PIC16C72 datasheet(83/128 Pages) MICROCHIP

83 / 128 page

PIC16C72 Series

 1998-2013 Microchip Technology Inc.

Preliminary

DS39016B-page 83

13.3

DC Characteristics:

PIC16C72/CR72-04 (Commercial, Industrial, Extended)

PIC16C72/CR72-10 (Commercial, Industrial, Extended)

PIC16C72/CR72-20 (Commercial, Industrial, Extended)

PIC16LC72/LCR72-04 (Commercial, Industrial)

DC CHARACTERISTICS

Standard Operating Conditions (unless otherwise stated)

Operating temperature

-40°C

 TA  +125°C for extended,

-40°C

 TA  +85°C for industrial and

0°C

 TA  +70°C for commercial

Operating voltage VDD range as described in DC spec Section 13.1 and

Section 13.2.

Param

No.

Characteristic

Sym

Min

Typ†

Max

Units

Conditions

Input Low Voltage

I/O ports

VIL

D030

with TTL buffer

VSS

0.15VDD

For entire VDD range

D030A

Vss

0.8V

4.5

 VDD 5.5V

D031

with Schmitt Trigger buffer

VSS

-0.2VDD

D032

MCLR, OSC1 (in RC mode)

VSS

-0.2VDD

D033

OSC1 (in XT, HS and LP)

VSS

-0.3VDD

Note1

Input High Voltage

I/O ports

VIH

D040

with TTL buffer

2.0

VDD

V4.5

 VDD 5.5V

D040A

0.25VDD +

0.8V

-VDD

For entire VDD range

D041

with Schmitt Trigger buffer

0.8VDD

-VDD

For entire VDD range

D042

MCLR

0.8VDD

-VDD

D042A

OSC1 (XT, HS and LP)

0.7VDD

Vdd

Note1

D043

OSC1 (in RC mode)

0.9VDD

-VDD

D070

PORTB weak pull-up current

IPURB

250

†400

AVDD = 5V, VPIN = VSS

Input Leakage Current (Notes 2, 3)

D060

I/O ports

IIL

1

AVss VPIN VDD, Pin at hi-

impedance

D061

MCLR, RA4/T0CKI

5

AVss VPIN VDD

D063

OSC1

5

AVss VPIN VDD, XT, HS and LP

osc configuration

Output Low Voltage

D080

I/O ports

VOL

0.6

IOL = 8.5 mA, VDD = 4.5V,

-40

C to +85C

D080A

0.6

IOL = 7.0 mA, VDD = 4.5V,

-40

C to +125C

D083

OSC2/CLKOUT (RC osc config)

0.6

IOL = 1.6 mA, VDD = 4.5V,

-40

C to +85C

D083A

0.6

IOL = 1.2 mA, VDD = 4.5V,

-40

C to +125C

These parameters are characterized but not tested.

†

Data in “Typ” column is at 5V, 25

C unless otherwise stated. These parameters are for design guidance only and are not

tested.

Note 1:

In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt trigger input. It is not recommended that the PIC16C7X be

driven with external clock in RC mode.

Note 2:

The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified levels repre-

sent normal operating conditions. Higher leakage current may be measured at different input voltages.

Note 3:

Negative current is defined as current sourced by the pin.

PIC16C72 Datasheet(PDF) 83 Page - Microchip Technology

PIC16C72 Datasheet(HTML) 83 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL