USB3300-EZK datasheet(13/59 Pages) MICROCHIP

13 / 59 page

Hi-Speed USB Host, Device or OTG PHY with ULPI Low Pin Interface

Datasheet

SMSC USB3300

Revision 1.1 (01-24-13)

DATASHEET

VDD3.3

Power

N/A

A 0.1uF bypass capacitor should be connected

between this pin and the ground plane on the PCB.

DATA[7]

I/O,

CMOS,

Pull-low

N/A

8-bit bi-directional data bus. Bus ownership is

determined by DIR. The Link and PHY initiate data

transfers by driving a non-zero pattern onto the data

bus. ULPI defines interface timing for a single-edge

data transfers with respect to rising edge of

CLKOUT. DATA[7] is the MSB and DATA[0] is the

LSB.

DATA[6]

I/O,

CMOS,

Pull-low

N/A

DATA[5]

I/O,

CMOS,

Pull-low

N/A

DATA[4]

I/O,

CMOS,

Pull-low

N/A

DATA[3]

I/O,

CMOS,

Pull-low

N/A

DATA[2]

I/O,

CMOS,

Pull-low

N/A

DATA[1]

I/O,

CMOS,

Pull-low

N/A

DATA[0]

I/O,

CMOS,

Pull-low

N/A

VDD3.3

Power

N/A

A 0.1uF bypass capacitor should be connected

between this pin and the ground plane on the PCB.

VDD1.8

Power

N/A

1.8V for digital circuitry on chip. Supplied by On-Chip

Regulator when REG_EN is active. When using the

internal regulators, place a 4.7uF low-ESR capacitor

near this pin and connect the capacitor from this pin

to ground. Connect pin 26 to pin 15. Do not connect

VDD1.8 to VDDA1.8 when using internal regulators.

When the regulators are disabled, pin 29 may be

connected to pins 26 and 15.

Output,

Analog

N/A

Crystal pin. If using an external clock on XI this pin

should be floated.

Input,

Analog

N/A

Crystal pin. A 24MHz crystal is supported. The

crystal is placed across XI and XO. An external

24MHz clock source may be driven into XI in place

of a crystal.

VDDA1.8

Power

N/A

1.8V for analog circuitry on chip. Supplied by On-

Chip Regulator when REG_EN is active. Place a

0.1uF capacitor near this pin and connect the

capacitor from this pin to ground. When using the

internal regulators, place a 4.7uF low-ESR capacitor

near this pin in parallel with the 0.1uF capacitor. Do

not connect VDD1.8A to VDD1.8 when using internal

regulators. When the regulators are disabled, pin 29

may be connected to pins 26 and 15.

Table 3.1 USB3300 Pin Definitions 32-Pin QFN Package (continued)

NAME

DIRECTION,

TYPE

ACTIVE

LEVEL

DESCRIPTION

USB3300-EZK Datasheet(PDF) 13 Page - Microchip Technology

USB3300-EZK Datasheet(HTML) 13 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59

Datasheet Download

Link URL