E5CN-R2ML-500 datasheet(63/72 Pages) OMRON

63 / 72 page

@N/E5@N-H

25.0

al1l

0.0

25.0

0.0

a-m

bank

rsp

0.0

sp-m

0.0

ct1

0.0

ct2

0.0

lcr1

0.0

lcr2

0.0

prst

rset

sktr

r-s

run

al-1

0.0

al-2

0.0

al2h

0.0

al2l

0.0

al-3

0.0

al3h

0.0

al3l

0.0

c-o

0.0

v-m

0.0

al1h

0.0

25.0

0.0

l.adj

off

cmwt

off

irda

off

spmd

lsp

ct1

0.0

ins

0.00

insh

0.00

insl

0.00

8.0

233.0

40.0

c-sc

1.00

c-db

0.0

of-r

50.0

hys

1.0

chys

1.0

soak

wt-b

off

mv-s

0.0

mv-e

0.0

sprt

off

ol-h

105.0

ol-l

-5.0

2.0

oc-h

0.8

sqrp

0.0

orl

0.0

ct2

0.0

lcr1

0.0

lcr2

0.0

hb1

0.0

hb2

0.0

hs1

50.0

hs2

50.0

oc1

50.0

oc2

50.0

100.0

Starting in manual mode.

Power ON

Starting in

automatic

mode.

Manual Control Level

PID

Control

only

PV/MV

Press the

O Key less than 1 s.

Operation Level

Adjustment Level

Display

Displayed only

once when

entering

adjustment level.

AT Execute/Cancel

Communications

Writing

Heater Current 1

Value Monitor

Heater Burnout

Detection 1

Heater Overcurrent

Detection 1

Heater Current 2

Value Monitor

Heater Burnout

Detection 2

Heater Overcurrent

Detection 2

Leakage Current 1

Monitor

Leakage Current 2

Monitor

HS Alarm 1

HS Alarm 2

Temperature Input Shift

1-point shift

2-point shift

Upper Limit

Temperature

Input Shift Value

Lower Limit

Temperature

Input Shift Value

Proportional Band

Integral Time

PID settings

Derivative Time

Cooling Coefficient

Heating/cooling

Dead Band

Manual Reset Value

Clear the offset during

stabilization of P or PD

control.

Hysteresis (Heating)

Hysteresis (Cooling)

Hysteresis settings

Soak Time

Wait Band

MV at Stop

MV at PV Error

SP Ramp Set Value

MV Upper Limit

MV Lower Limit

MV Change Rate Limit

Process Value

Added when Additional

PV display is ON.

Process Value/

Set Point

Auto/Manual Switch

PID control only.

Added when

auto/manual select

addition is ON.

Set Point During

SP Ramp

Heater Current 1 Value

Monitor

Heater Current 2 Value

Monitor

Leakage Current 1

Monitor

Leakage Current 2

Monitor

Program Start

Soak Time Remain

Press the

and

M Keys for

at least 3 s.

RUN/STOP

Alarm Value 1

Alarm Value

Upper Limit 1

Alarm Value

Lower Limit 1

Alarm Value 2

Alarm Value

Upper Limit 2

Alarm Value

Lower Limit 2

Alarm Value 3

Alarm Value

Upper Limit 3

Alarm Value

Lower Limit 3

MV Monitor (Heating)

MV Monitor (Cooling)

Press the PF Key

for at least 1 s.

Press the

Key or the PF

Key for at least

1 s.

✽1

Press

the

Key for

at least

3 s.

Set either

of these

param-

eters.

Extraction of Square

Root

Low-cut Point

Press the

and

M Keys for

at least 1 s.

PF Key

✽2

PF Key

✽2

Monitor/Setting Item Level (E5AN-H/E5EN-H only)

Monitor/Setting

Item Display 1

Monitor/Setting

Item Display 2

Monitor/Setting

Item Display 3

Monitor/Setting

Item Display 4

Monitor/Setting

Item Display 5

Note: The monitor/setting items to be displayed is set in the Monitor/Setting Item 1 to

5 parameters (advanced function setting level).

Infrared Communications Use

SP Mode

Position Proportional

Dead Band

Open/Close Hysteresis

Bank No.

Remote SP Monitor

Valve Opening

Monitor

✽1

✽1. When the PF Setting parameter is set to A-M for a Controller with a PF Key (E5AN-H/E5EN-H).

✽2. When the PF Setting parameter is set to PFDP for a Controller with a PF Key (E5AN-H/E5EN-H).

E5CN-R2ML-500 Datasheet(PDF) 63 Page - Omron Electronics LLC

E5CN-R2ML-500 Datasheet(HTML) 63 Page - Omron Electronics LLC

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72

Datasheet Download

Link URL