PIC24HJ128GP310 datasheet(165/286 Pages) MICROCHIP

165 / 286 page

DS70175F-page 163

PIC24HJXXXGPX06/X08/X10

17.0 UNIVERSAL ASYNCHRONOUS

RECEIVER TRANSMITTER

(UART)

The Universal Asynchronous Receiver Transmitter

(UART) module is one of the serial I/O modules avail-

able in the PIC24HJXXXGPX06/X08/X10 device fam-

ily. The UART is a full-duplex asynchronous system

that can communicate with peripheral devices, such as

personal computers, LIN, RS-232 and RS-485 inter-

faces. The module also supports a hardware flow con-

trol option with the UxCTS and UxRTS pins and also

includes an IrDA® encoder and decoder.

The primary features of the UART module are:

• Full-Duplex, 8 or 9-bit Data Transmission through

the UxTX and UxRX pins

• Even, Odd or No Parity Options (for 8-bit data)

• One or Two Stop bits

• Hardware Flow Control Option with UxCTS and

UxRTS pins

• Fully Integrated Baud Rate Generator with 16-bit

Prescaler

• Baud Rates Ranging from 1 Mbps to 15 bps at

16 MIPS

• 4-deep First-In-First-Out (FIFO) Transmit Data

Buffer

• 4-Deep FIFO Receive Data Buffer

• Parity, Framing and Buffer Overrun Error Detection

• Support for 9-bit mode with Address Detect

(9th bit = 1)

• Transmit and Receive Interrupts

• A Separate Interrupt for all UART Error Conditions

• Loopback mode for Diagnostic Support

• Support for Sync and Break Characters

• Supports Automatic Baud Rate Detection

• IrDA Encoder and Decoder Logic

• 16x Baud Clock Output for IrDA Support

A simplified block diagram of the UART is shown in

Figure 17-1. The UART module consists of the key

important hardware elements:

• Baud Rate Generator

• Asynchronous Transmitter

• Asynchronous Receiver

FIGURE 17-1:

UART SIMPLIFIED BLOCK DIAGRAM

Note:

This data sheet summarizes the features

of this group of PIC24HJXXXGPX06/X08/

X10 devices. It is not intended to be a

comprehensive reference source. To com-

plement the information in this data sheet,

refer to the “PIC24H Family Reference

Manual”. Refer to the Microchip web site

(www.microchip.com)

for

the

latest

PIC24H

Family

Reference

Manual

sections.

Note 1: Both UART1 and UART2 can trigger a DMA data transfer. If U1TX, U1RX, U2TX or U2RX is selected as

a DMA IRQ source, a DMA transfer occurs when the U1TXIF, U1RXIF, U2TXIF or U2RXIF bit gets set as

a result of a UART1 or UART2 transmission or reception.

2: If DMA transfers are required, the UART TX/RX FIFO buffer must be set to a size of 1 byte/word

(i.e., UTXISEL<1:0> = 00 and URXISEL<1:0> = 00).

UxRX

Hardware Flow Control

UART Receiver

UART Transmitter

UxTX

BCLK

Baud Rate Generator

UxRTS

IrDA®

UxCTS

PIC24HJ128GP310 Datasheet(PDF) 165 Page - Microchip Technology

PIC24HJ128GP310 Datasheet(HTML) 165 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL