DSPIC33FJ64GP706 datasheet(188/322 Pages) MICROCHIP

188 / 322 page

dsPIC33FJXXXGPX06/X08/X10

DS70286C-page 186

UxMODE: UARTx MODE REGISTER

R/W-0

U-0

R/W-0

U-0

R/W-0

UARTEN(1)

—

USIDL

IREN(2)

RTSMD

—UEN<1:0>

bit 15

bit 8

R/W-0 HC

R/W-0

R/W-0 HC

R/W-0

WAKE

LPBACK

ABAUD

URXINV

BRGH

PDSEL<1:0>

STSEL

bit 7

bit 0

Legend:

HC = Hardware cleared

R = Readable bit

W = Writable bit

U = Unimplemented bit, read as ‘0’

-n = Value at POR

‘1’ = Bit is set

‘0’ = Bit is cleared

x = Bit is unknown

bit 15

UARTEN: UARTx Enable bit(1)

= UARTx is enabled; all UARTx pins are controlled by UARTx as defined by UEN<1:0>

= UARTx is disabled; all UARTx pins are controlled by port latches; UARTx power consumption

minimal

bit 14

Unimplemented: Read as ‘0’

bit 13

USIDL: Stop in Idle Mode bit

= Discontinue module operation when device enters Idle mode

= Continue module operation in Idle mode

bit 12

IREN: IrDA® Encoder and Decoder Enable bit(2)

=IrDA® encoder and decoder enabled

=IrDA® encoder and decoder disabled

bit 11

RTSMD: Mode Selection for UxRTS Pin bit

=UxRTS pin in Simplex mode

=UxRTS pin in Flow Control mode

bit 10

Unimplemented: Read as ‘0’

bit 9-8

UEN<1:0>: UARTx Enable bits

= UxTX, UxRX and BCLK pins are enabled and used; UxCTS pin controlled by port latches

= UxTX, UxRX, UxCTS and UxRTS pins are enabled and used

= UxTX, UxRX and UxRTS pins are enabled and used; UxCTS pin controlled by port latches

= UxTX and UxRX pins are enabled and used; UxCTS and UxRTS/BCLK pins controlled by

port latches

bit 7

WAKE: Wake-up on Start bit Detect During Sleep Mode Enable bit

= UARTx will continue to sample the UxRX pin; interrupt generated on falling edge; bit cleared

in hardware on following rising edge

= No wake-up enabled

bit 6

LPBACK: UARTx Loopback Mode Select bit

= Enable Loopback mode

= Loopback mode is disabled

bit 5

ABAUD: Auto-Baud Enable bit

= Enable baud rate measurement on the next character - requires reception of a Sync field (55h)

before other data; cleared in hardware upon completion

= Baud rate measurement disabled or completed

Note 1: Refer to Section 17. “UART” (DS70188) in the “dsPIC33F Family Reference Manual” for information on

enabling the UART module for receive or transmit operation.

2: This feature is only available for the 16x BRG mode (BRGH = 0).

DSPIC33FJ64GP706 Datasheet(PDF) 188 Page - Microchip Technology

DSPIC33FJ64GP706 Datasheet(HTML) 188 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL