| Electronic Components Datasheet Search |
|
LTC1735IGN-1 Datasheet(PDF) 24 Page - Linear Technology |
|
|
|||||||||||||||||||||||||||||
LTC1735IGN-1 Datasheet(HTML) 24 Page - Linear Technology |
|
24 / 28 page ![]() 24 LTC1735-1 Design Example As a design example, assume VIN = 12V (nominal), VIN = 22V (max), VOUT = 1.5V, IMAX = 12A and f = 300kHz, RSENSE and COSC can immediately be calculated: RSENSE = 50mV/12A = 0.042Ω COSC = 1.61(107)/(300kHz) – 11pF = 43pF Assume a 1.2 µH inductor and check the actual value of the ripple current. The following equation is used : ∆I V fL V V L OUT OUT IN = ()( ) – 1 The highest value of the ripple current occurs at the maximum input and output voltages: ∆I V kHz H V V A L = µ = 15 300 1 2 1 15 22 39 . (. ) – . . The maximum ripple current is 32% of maximum output current, which is about right. Next, verify the minimum on-time of 200ns is not violated. The minimum on-time occurs at maximum VIN and mini- mum VOUT. t V Vf V V kHz ns ON MIN OUT IN MAX () () . () == = 15 22 300 227 The power dissipation on the topside MOSFET can be easily estimated. Choosing a Fairchild FDS6612A results in; RDS(ON) = 0.03Ω, CRSS = 80pF. At maximum input voltage with T(estimated) = 50 °C: P V V CC V A pF kHz mW MAIN = () +° ° [] Ω () + () ()( )( ) = 15 22 12 1 0 005 50 25 0 03 1 7 22 12 80 300 568 2 2 . ( . )( – ) . . Because the duty cycle of the bottom MOSFET is much greater than the top, two larger MOSFETs must be paral- leled. Choosing Fairchild FDS6680A MOSFETs yields a parallel RDS(ON) of 0.0065Ω. The total power dissipation for both bottom MOSFETs, again assuming T = 50 °C, is: P VV V A mW SYNC = () ( ) Ω () = 22 1 5 22 12 1 1 0 0065 959 2 –. .. Thanks to current foldback, the bottom MOSFET dissipa- tion in short circuit will be less than under full-load conditions. CIN is chosen for an RMS current rating of at least 6A at temperature. COUT is chosen with an ESR of 0.01Ω for low output ripple. The output ripple in continuous mode will be highest at the maximum input voltage. The output voltage ripple due to ESR is approximately: VORIPPLE = RESR(∆IL) = 0.01Ω(3.9A) = 39mVP-P Since the output voltage is below 2.4V, the output resistive divider will need to be sized to not only set the output voltage but also to absorb the SENSE pins specified input current. R MAX k V VV k 124 08 24 15 21 3 () . .– . . = = Choosing 1% resistors: R1 = 21k and R2 = 18.7k yields an output voltage of 1.512V. PC Board Layout Checklist When laying out the printed circuit board, the following checklist should be used to ensure proper operation of the LTC1735-1. These items are also illustrated graphically in the layout diagram of Figure 12. Check the following in your layout: 1. Are the signal and power grounds segregated? The LTC1735-1 PGND pin should tie to the ground plane close to the input capacitor(s). The SGND pin should then connect to PGND and all components that connect to SGND should make a single-point tie to the SGND pin. The synchronous MOSFET source should connect to the input capacitor(s) ground. 2. Does the VOSENSE pin connect directly to the feedback resistors? The resistive divider R1, R2 must be con- nected between the (+) plate of COUT and signal ground. The 47pF capacitor from VOSENSE to SGND should be as close as possible to the LTC1735-1. Be careful locating the feedback resistors too far away from the APPLICATIO S I FOR ATIO |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |