| Electronic Components Datasheet Search |
|
PIC16C770-04/P Datasheet(PDF) 64 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
PIC16C770-04/P Datasheet(HTML) 64 Page - Microchip Technology |
|
64 / 200 page ![]() PIC16C717/770/771 DS41120A-page 64 Advanced Information © 1999 Microchip Technology Inc. 8.3.5 PROGRAMMABLE DEADBAND DELAY In half-bridge or full-bridge applications, where all power switches are modulated at the PWM frequency at all time, the power switches normally require longer time to turn off than to turn on. If both the upper and lower power switches are switched at the same time (one turned on, and the other turned off), both switches will be on for a short period of time, until one switch completely turns off. During this time, a very high cur- rent, called shoot-through current, will flow through both power switches, shorting the bridge supply. To avoid this potentially destructive shoot-through current from flowing during switching, turning on the power switch is normally delayed to allow the other switch to completely turn off. In the Half-Bridge Output mode, a digitally program- mable deadband delay is available to avoid shoot- through current from destroying the bridge power switches. The delay occurs at the signal transition from the non-active state to the active state. See Figure 8-6 for illustration. The P1DEL register sets the amount of delay. REGISTER 8-2: PWM DELAY REGISTER (P1DEL: 97H) 8.3.6 DIRECTION CHANGE IN FULL-BRIDGE OUTPUT MODE In the Full-Bridge Output mode, the PWM1M1 bit in the CCP1CON register allows user to control the Forward/ Reverse direction. When the application firmware changes this direction control bit, the ECCP module will assume the new direction on the next PWM cycle. The current PWM cycle still continues, however, the non- modulated outputs, P1A and P1C signals, will transition to the new direction TOSC, 4 •TOSC or 16•TOSC (for Timer2 presale T2CKRS<1:0> = 00, 01 and 1x respec- tively) earlier, before the end of the period. During this transition cycle, the modulated outputs, P1B and P1D, will go to the inactive state. See Figure 8-10 for illustra- tion. FIGURE 8-10: PWM DIRECTION CHANGE R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ - n = Value at POR reset bit7 bit0 bit 7-0: P1DEL<7:0>: PWM Delay count for Half-Bridge output mode: Number of FOSC/4 (Tosc •4) cycles between the P1A transition and the P1B transition. DC PERIOD SIGNAL P1A (Active High) P1B (Active High) P1C (Active High) P1D (Active High) Note 1: The Direction bit in the ECCP Control Register (CCP1CON.PWM1M1) is written anytime during the PWM cycle. 2: The P1A and P1C signals switch TOSC, 4*Tosc or 16*TOSC depending on the Timer2 prescaler value earlier when changing direction. The modulated P1B and P1D signals are inactive at this time. (1) PERIOD (2) |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |