PIC16C72A-04SLASHP datasheet(47/120 Pages) MICROCHIP

47 / 120 page

PIC16C62B/72A

Preliminary

DS35008B-page 47

SSPCON: SYNC SERIAL PORT CONTROL REGISTER (ADDRESS 14h)

R/W-0

WCOL

SSPOV

SSPEN

CKP

SSPM3

SSPM2

SSPM1

SSPM0

R = Readable bit

W = Writable bit

U = Unimplemented bit, read

as ‘0’

- n =Value at POR reset

bit7

bit0

bit 7:

WCOL: Write Collision Detect bit

= The SSPBUF register is written while it is still transmitting the previous word

(must be cleared in software)

= No collision

bit 6:

SSPOV: Receive Overflow Indicator bit

In SPI mode

= A new byte is received while the SSPBUF register is still holding the previous data. In case of overflow,

the data in SSPSR is lost. Overflow can only occur in slave mode. The user must read the SSPBUF, even

if only transmitting data, to avoid setting overflow. In master operation, the overflow bit is not set since

each new reception (and transmission) is initiated by writing to the SSPBUF register.

= No overflow

In I2C mode

= A byte is received while the SSPBUF register is still holding the previous byte. SSPOV is a "don’t care"

in transmit mode. SSPOV must be cleared in software in either mode.

= No overflow

bit 5:

SSPEN: Synchronous Serial Port Enable bit

In SPI mode

= Enables serial port and configures SCK, SDO, and SDI as serial port pins

= Disables serial port and configures these pins as I/O port pins

In I2C mode

1 = Enables the serial port and configures the SDA and SCL pins as serial port pins

0 = Disables serial port and configures these pins as I/O port pins

In both modes, when enabled, these pins must be properly configured as input or output.

bit 4:

CKP: Clock Polarity Select bit

In SPI mode

= Idle state for clock is a high level

= Idle state for clock is a low level

In I2C mode

SCK release control

= Enable clock

= Holds clock low (clock stretch)

bit 3-0: SSPM3:SSPM0: Synchronous Serial Port Mode Select bits

0000

= SPI master operation, clock = FOSC/4

0001

= SPI master operation, clock = FOSC/16

0010

= SPI master operation, clock = FOSC/64

0011

= SPI master operation, clock = TMR2 output/2

0100

= SPI slave mode, clock = SCK pin. SS pin control enabled.

0101

= SPI slave mode, clock = SCK pin. SS pin control disabled. SS can be used as I/O pin

0110

= I2C slave mode, 7-bit address

0111

= I2C slave mode, 10-bit address

1011

= I2C firmware controlled master operation (slave idle)

1110

= I2C slave mode, 7-bit address with start and stop bit interrupts enabled

1111

= I2C slave mode, 10-bit address with start and stop bit interrupts enabled

PIC16C72A-04/P Datasheet(PDF) 47 Page - Microchip Technology

PIC16C72A-04/P Datasheet(HTML) 47 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL