PIC17C752-08SLASHCL datasheet(191/328 Pages) MICROCHIP

191 / 328 page

DS30289A-page 191

PIC17C7XX

17.3

Watchdog Timer (WDT)

The Watchdog Timer’s function is to recover from

software malfunction. The WDT uses an internal free

running on-chip RC oscillator for its clock source. This

does not require any external components. This RC

oscillator is separate from the RC oscillator of the

OSC1/CLKIN pin. That means that the WDT will run,

even

the

clock

the

OSC1/CLKIN

and

OSC2/CLKOUT pins have been stopped, for example,

by execution of a SLEEP instruction. During normal

operation, a WDT time-out generates a device RESET.

The

WDT

can

permanently

disabled

programming the conﬁguration bits WDTPS1:WDTPS0

as '00' (Section 17.1).

Under normal operation, the WDT must be cleared on

a regular interval. This time must be less than the min-

imum WDT overﬂow time. Not clearing the WDT in this

time frame will cause the WDT to overﬂow and reset the

device.

17.3.1

WDT PERIOD

The WDT has a nominal time-out period of 12 ms, (with

postscaler = 1). The time-out periods vary with temper-

ature, VDD and process variations from part to part (see

DC specs). If longer time-out periods are desired, con-

ﬁguration bits should be used to enable the WDT with

a greater prescale. Thus, typical time-out periods up to

3.0 seconds can be realized.

The CLRWDT and SLEEP instructions clear the WDT

and its postscale setting and prevent it from timing out

thus generating a device RESET condition.

The TO bit in the CPUSTA register will be cleared upon

a WDT time-out.

17.3.2

CLEARING THE WDT AND POSTSCALER

The WDT and postscaler are cleared when:

• The device is in the reset state

•A SLEEP instruction is executed

•A CLRWDT instruction is executed

• Wake-up from SLEEP by an interrupt

The WDT counter/postscaler will start counting on the

ﬁrst edge after the device exits the reset state.

17.3.3

WDT PROGRAMMING CONSIDERATIONS

It should also be taken in account that under worst case

conditions (VDD = Min., Temperature = Max., max.

WDT postscaler) it may take several seconds before a

WDT time-out occurs.

The WDT and postscaler become the Power-up Timer

whenever the PWRT is invoked.

17.3.4

WDT AS NORMAL TIMER

When the WDT is selected as a normal timer, the clock

source is the device clock. Neither the WDT nor the

postscaler are directly readable or writable. The over-

ﬂow time is 65536 TOSC cycles. On overﬂow, the TO bit

is cleared (device is not reset). The CLRWDT instruction

can be used to set the TO bit. This allows the WDT to

be a simple overﬂow timer. The simple timer does not

increment when in sleep.

FIGURE 17-2: WATCHDOG TIMER BLOCK DIAGRAM

TABLE 17-2:

REGISTERS/BITS ASSOCIATED WITH THE WATCHDOG TIMER

Address

Name

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Value on

POR,

BOR

MCLR, WDT

—

Conﬁg

See Figure 17-1 for location of WDTPSx bits in Conﬁguration Word.

(Note 1)

06h, Unbanked

CPUSTA

—

STKAV

GLINTD

POR

BOR

--11 11qq

--11 qquu

Legend:

= unimplemented read as '0', q - value depends on condition, shaded cells are not used by the WDT.

Note 1:

This value will be as the device was programmed, or if unprogrammed, will read as all '1's.

WDT

WDT Enable

Postscaler

4 - to - 1 MUX

WDTPS1:WDTPS0

On-chip RC

WDT Overﬂow

Oscillator(1)

Note 1: This oscillator is separate from the external

RC oscillator on the OSC1 pin.

PIC17C752-08/CL Datasheet(PDF) 191 Page - Microchip Technology

PIC17C752-08/CL Datasheet(HTML) 191 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL