| Electronic Components Datasheet Search |
|
LX1563IDM Datasheet(PDF) 13 Page - Microsemi Corporation |
|
|
|||||||||||||||||||||||||||||
LX1563IDM Datasheet(HTML) 13 Page - Microsemi Corporation |
|
13 / 25 page ![]() SECOND-GENERATION POWER FACTOR C ONTROLLER LX1562/1563 PRODUCT DA T ABOOK 1996/1997 13 Copyright © 1996 Rev. 1.3 12/96 P RODUCTION D ATA S HEET FUNCTIONAL DESCRIPTION The operation of the IC is best described by referring to the block-diagram. The output of the multiplier stage generates a voltage proportional to the product of the rectified AC line and the output of the error amplifier. This voltage serves as the reference for the inductor peak current that is sensed by the resistor in series with the external power MOSFET. When the sense voltage exceeds this threshold, C.S. comparator trips and resets the latch as well as turning the power MOSFET off. The energy stored during switch on-time is now transferred and stored in the output capacitor, causing the inductor current to ramp down. When current reaches zero level (inductor runs out of energy) , boost diode (D1) stops conducting and the residual inductor energy and the drain to source capacitance of the power MOSFET create an LC tank circuit which causes drain voltage to resonate at this frequency. The resonating voltage is detected by the secondary winding (Idet winding) of the in- ductor. When this voltage swings negative “I detect” pin senses it and activates the blanking circuit , sets the latch, and turns power MOSFET on, repeating the cycle. This operation contin- ues for the entire cycle of the AC rectified input resulting in an inductor current as shown in Figure 23. The high frequency content of this current is then filtered by the input capacitor (C1) resulting in a sine wave input current in phase with the AC line voltage. Output voltage regulation is accomplished when the error amplifier compares this voltage to an internal 2.5V reference and generates an error voltage. This voltage then controls the amplitude of the multiplier output adjusting the peak inductor current proportional to the load and line variations, maintain- ing a well regulated voltage. IC DESCRIPTION UNDERVOLTAGE LOCK OUT The LX1562/63 undervoltage lock-out is designed to maintain an ultra low quiescent current of less than 300µA, while guar- anteeing the IC is fully functional before the output stage is activated. Comparing this to the SG3561A device, a 40% reduc- tion in start-up current is achieved, resulting in 40% less power dissipation in the start-up resistor. This is especially important in electronic ballast applications that are designed to operate in harsh environments, with convection cooling as the only means of heat dissipation. Figure 24 shows an efficient supply voltage using the ultra low start-up current of the LX1562 in conjunction with a boot- strap winding off of the power transformer. Circuit operation is as follows: The start-up capacitor (C1) is charged by current through resistor (R1) minus the start-up current drawn by the IC. This resistor is typically chosen to provide 2X the maximum start-up current at low line to guarantee start-up under the worst case condition. Once the capacitor voltage reaches the start-up threshold, the IC turns on, starting the switching cycle. The operation of the IC demands an increase in operating current which results in discharging the capacitor. During the discharge cycle, the flyback voltage of the auxiliary winding is rectified and filtered via rectifier (D1) and charges the capacitor above the minimum operating voltage of the device and takes over as the supply voltage. The start-up capacitor and auxiliary wind- ing must be selected such that it satisfies worst case IC condi- tions. Figure 25 shows start-up time and voltage of capacitor C1. Table 1 shows the start-up voltage and hysteresis for LX1562 and LX1563. The LX1562 is used for stand alone pre-regulator applications while LX1563 is ideal for applications where sup- ply voltage is derived elsewhere and requires less than 14V start-up. Part # Start-Up Hysteresis Voltage Voltage LX1562 13.1V 5.2V LX1563 9.8V 2.1V T ABLE 1 Rectified AC Line GND LX1562 GND V O V IN I ST < 300µA I 1 > 300µA C1 R1 R S D1 FIGURE 24 — TYPICAL APPLICATION OF START-UP CIRCUITRY Inductor Peak Current Envelope Average AC Input Current I L T ON T OFF FIGURE 23 — INDUCTOR CURRENT |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |