LM324MTSLASHNOPB datasheet(6/34 Pages) TI1

6 / 34 page

LM124-N, LM224-N

LM2902-N, LM324-N

SNOSC16D – MARCH 2000 – REVISED JANUARY 2015

www.ti.com

Electrical Characteristics: LM124A/224A/324A (continued)

+ = 5.0 V, (1), unless otherwise stated

LM124A

LM224A

LM324A

PARAMETER

TEST CONDITIONS

UNIT

MIN

TYP

MAX

MIN

TYP

MAX

MIN

TYP

MAX

IOS Drift

RS = 0 Ω

200

300

pA/°C

Input Bias Current

IIN(+) or IIN(−)

100

200

Input Common-Mode

V+ = 30 V,

V+

−2

V+

−2

V+

−2

Voltage Range(4)

(LM2902-N, V+ = 26 V)

Large Signal

V+ = 15 V (VOSwing = 1 V to 11 V),

V/mV

Voltage Gain

RL ≥ 2 kΩ

RL = 2 kΩ

V+ = 30 V

Output

VOH

(LM2902-N,

RL = 10 kΩ

Voltage

V+ = 26 V)

Swing

VOL

V+ = 5 V, RL = 10 kΩ

VIN

+ = +1V,

Source

VIN

− = 0V,

V+ = 15V

Output

VO = 2 V

Current

VIN

− = +1V,

Sink

VIN

+ = 0V,

V+ = 15V

6.6 Electrical Characteristics: LM124-N/224-N/324-N/2902-N

+ = +5.0V, (1), unless otherwise stated

LM124-N / LM224-N

LM324-N

LM2902-N

PARAMETER

TEST CONDITIONS

UNIT

MIN

TYP

MAX

MIN

TYP

MAX

MIN

TYP

MAX

Input Offset Voltage

TA = 25°C

(2)

Input Bias Current(3)

IIN(+) or IIN(−), VCM = 0 V, TA = 25°C

150

250

Input Offset Current

IIN(+) or IIN(−), VCM = 0 V, TA = 25°C

Input Common-Mode Voltage

V+ = 30 V, (LM2902-N, V+ = 26V),

V+

−1.

V+

−1.

V+

−1.

Range(4)

TA = 25°C

Over Full Temperature Range

RL = ∞ On All Op Amps,

1.5

Supply Current

V+ = 30 V (LM2902-N V+ = 26 V)

0.7

1.2

0.7

1.2

0.7

1.2

V+ = 5 V

V+ = 15V, RL≥ 2 kΩ,

Large Signal Voltage Gain

100

V/mV

(VO = 1 V to 11 V), TA = 25°C

Common-Mode Rejection

DC, VCM = 0 V to V

+ − 1.5 V, T

A = 25°C

Ratio

V+ = 5 V to 30 V (LM2902-N,

Power Supply Rejection Ratio

100

V+ = 5 V to 26 V), TA = 25°C

Amplifier-to-Amplifier

f = 1 kHz to 20 kHz, TA = 25°C

−120

Coupling(5)

(Input Referred)

(1)

These specifications are limited to

−55°C ≤ TA ≤ +125°C for the LM124-N/LM124A. With the LM224-N/LM224A, all temperature

specifications are limited to

−25°C ≤ TA ≤ +85°C, the LM324-N/LM324A temperature specifications are limited to 0°C ≤ TA ≤ +70°C, and

the LM2902-N specifications are limited to

−40°C ≤ TA ≤ +85°C.

(2)

VO ≃ 1.4V, RS = 0 Ω with V

+ from 5 V to 30 V; and over the full input common-mode range (0 V to V+ − 1.5 V) for LM2902-N, V+ from 5

V to 26 V.

(3)

The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the

state of the output so no loading change exists on the input lines.

(4)

The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3 V (at 25°C). The

upper end of the common-mode voltage range is V+

− 1.5 V (at 25°C), but either or both inputs can go to 32 V without damage (26 V for

LM2902-N), independent of the magnitude of V+.

(5)

Due to proximity of external components, insure that coupling is not originating via stray capacitance between these external parts. This

typically can be detected as this type of capacitance increases at higher frequencies.

Submit Documentation Feedback

Product Folder Links: LM124-N LM224-N LM2902-N LM324-N

LM324MT/NOPB Datasheet(PDF) 6 Page - Texas Instruments

LM324MT/NOPB Datasheet(HTML) 6 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34

Datasheet Download

Link URL