| Electronic Components Datasheet Search |
|
205-MC2 Datasheet(PDF) 21 Page - List of Unclassifed Manufacturers |
|
|
|||||||||||||||||||||||||||||
205-MC2 Datasheet(HTML) 21 Page - List of Unclassifed Manufacturers |
|
21 / 22 page ![]() 16 3 3..8 8 D Diis sa as ss se em mb blly y//A As ss se em mb blly y You must go through the following steps in order to remove the printed circuit board from the case if you want to change from 115 Vac to 230 Vac (or vice versa) or to change from Fahrenheit to Celsius (or vice versa). These changes must be performed by a qualified technician in order to avoid damage to the unit. WARNING: Do not connect ac power to your meter until you have completed all input and output connections. Failure to do so may result in injury! 1. Remove power and all wire connections from the unit. 2. Unplug the three connectors (P1, P2, and P3) from the back of the meter. Grasp them firmly on the top and bottom of the connector and pull. Figure 3-9 shows the location of the three connectors. 3. Remove the lens, mounting screws, and mounting clamp from the unit as described in steps 1 and 2 in Section 3. Slide the unit out of the panel (if it is installed in a panel). 4. The printed circuit board is held in place by a tab and notch system located next to the P1 connector, pin 1 (refer to Figure 3-9). The tab is on the case and the notch is on the edge of the PC Board. Hold the meter with the display facing away from you. Gently pry the tab (on the back corner of the case) out with the edge of your finger, while pushing the back of the PC Board out through the front of the meter. The PC Board will slide out the front, free from the case. 13 3 3..6 6 D Diis sp plla ay y H Ho olld d C Co on nn ne ec cttiio on ns s The “Display Hold” function can be used to freeze the display. Connect a single pole, single throw (SPST) switch between pins 1 and 2 on the P2 connector. The display will stop updating when this switch is on. When this switch is off, the display will update itself 2.5 times per second. To access the “Display Hold” function, attach copper wire to the 3-pin female connector that is supplied with the meter. Refer to Figure 3-6 for wiring instructions. This connector shares a common return with the Analog Output. Plug the female connector into the P2 connector at the rear of the meter. Figure 2-2 shows the location of the P2 connector on the meter. Figure 3-6. Display Hold Connections 1 2 3 RETURN Screws underneath Display Hold Switch P2 16 3 3..8 8 D Diis sa as ss se em mb blly y//A As ss se em mb blly y You must go through the following steps in order to remove the printed circuit board from the case if you want to change from 115 Vac to 230 Vac (or vice versa) or to change from Fahrenheit to Celsius (or vice versa). These changes must be performed by a qualified technician in order to avoid damage to the unit. WARNING: Do not connect ac power to your meter until you have completed all input and output connections. Failure to do so may result in injury! 1. Remove power and all wire connections from the unit. 2. Unplug the three connectors (P1, P2, and P3) from the back of the meter. Grasp them firmly on the top and bottom of the connector and pull. Figure 3-9 shows the location of the three connectors. 3. Remove the lens, mounting screws, and mounting clamp from the unit as described in steps 1 and 2 in Section 3. Slide the unit out of the panel (if it is installed in a panel). 4. The printed circuit board is held in place by a tab and notch system located next to the P1 connector, pin 1 (refer to Figure 3-9). The tab is on the case and the notch is on the edge of the PC Board. Hold the meter with the display facing away from you. Gently pry the tab (on the back corner of the case) out with the edge of your finger, while pushing the back of the PC Board out through the front of the meter. The PC Board will slide out the front, free from the case. 13 3 3..6 6 D Diis sp plla ay y H Ho olld d C Co on nn ne ec cttiio on ns s The “Display Hold” function can be used to freeze the display. Connect a single pole, single throw (SPST) switch between pins 1 and 2 on the P2 connector. The display will stop updating when this switch is on. When this switch is off, the display will update itself 2.5 times per second. To access the “Display Hold” function, attach copper wire to the 3-pin female connector that is supplied with the meter. Refer to Figure 3-6 for wiring instructions. This connector shares a common return with the Analog Output. Plug the female connector into the P2 connector at the rear of the meter. Figure 2-2 shows the location of the P2 connector on the meter. Figure 3-6. Display Hold Connections 1 2 3 RETURN Screws underneath Display Hold Switch P2 |
|
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |