DLPC3430 datasheet(8/59 Pages) TI1

8 / 59 page

DLPC3430, DLPC3435

DLPS038B – JULY 2014 – REVISED FEBRUARY 2016

www.ti.com

Product Folder Links: DLPC3430 DLPC3435

Submit Documentation Feedback

(1)

External pullup resistor must be 8 k

Ω or less.

(2)

For more information about usage, see HOST_IRQ Usage Model.

Pin Functions – Peripheral Interface(1)

I/O

DESCRIPTION

NAME

NUMBER

CMP_OUT

A12

Successive approximation ADC comparator output (DLPC343x Input). Assumes a successive

approximation ADC is implemented with a WPC light sensor and/or a thermistor feeding one input of

an external comparator and the other side of the comparator is driven from the ASIC’s CMP_PWM pin.

Should be pulled-down to ground if this function is not used. (hysteresis buffer)

CMP_PWM

A15

Successive approximation comparator pulse-duration modulation (output). Supplies a PWM signal to

drive the successive approximation ADC comparator used in WPC light-to-voltage sensor applications.

Should be left unconnected if this function is not used.

HOST_IRQ(2)

Host interrupt (output)

This signal has two primary uses. The first use is to indicate when DLPC343x auto-initialization is in

progress and most importantly when it completes. The second is to indicate when service is requested

(that is an interrupt request).

The DLPC343x tri-states this output during reset and assumes that an external pullup is in place to

drive this signal to its inactive state.

IIC0_SCL

N10

I2C slave (port 0) SCL (bidirectional, open-drain signal with input hysteresis): An external pullup is

required. The slave I2C I/Os are 3.6-V tolerant (high-volt-input tolerant) and are powered by VCC_INTF

(which can be 1.8, 2.5, or 3.3 V). External I2C pullups must be connected to an equal or higher supply

voltage, up to a maximum of 3.6 V (a lower pullup supply voltage would not likely satisfy the VIH

specification of the slave I2C input buffers).

Reserved

R11

TI internal use. TI recommends an external pullup resistor.

IIC0_SDA

I2C slave (port 0) SDA. (bidirectional, open-drain signal with input hysteresis): An external pullup is

required. The slave I2C port is the control port of ASIC. The slave I2C I/Os are 3.6-V tolerant (high-volt-

input tolerant) and are powered by VCC_INTF (which can be 1.8, 2.5, or 3.3 V). External I2C pullups

must be connected to an equal or higher supply voltage, up to a maximum of 3.6 V (a lower pullup

supply voltage would not likely satisfy the VIH specification of the slave I2C input buffers).

Reserved

R10

TI internal use. TI recommends an external pullup resistor.

LED_SEL_0

B15

LED enable select. Controlled by programmable DMD sequence

Timing

LED_SEL(1:0)

Enabled LED

DLPA2000 application

None

Red

Green

Blue

LED_SEL_1

B14

These signals will be driven low when RESETZ is asserted and the corresponding I/O power is

supplied. They will continue to be driven low throughout the auto-initialization process. A weak,

external pulldown resistor is still recommended to ensure that the LEDs are disabled when I/O power is

not applied.

SPI0_CLK

A13

O13

Synchronous serial port 0, clock

SPI0_CSZ0

A14

O13

SPI port 1, chip select 0 (active low output)

TI recommends an external pullup resistor to avoid floating inputs to the external SPI device during

ASIC reset assertion.

SPI0_CSZ1

C12

O13

SPI port 1, chip select 1 (active low output)

TI recommends an external pullup resistor to avoid floating inputs to the external SPI device during

ASIC reset assertion.

SPI0_DIN

B12

I12

Synchronous serial port 0, receive data in

SPI0_DOUT

B13

O13

Synchronous serial port 0, transmit data out

DLPC3430 Datasheet(PDF) 8 Page - Texas Instruments

DLPC3430 Datasheet(HTML) 8 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59

Datasheet Download

Link URL