www.micropowerdirect.com

Model Selection Guide

Model

Number

Input

Output

Over Volt.

Protection

(VDC)

Capacitive

Load

(µF, Max)

Efficiency

(%, Typ)

Voltage

(VDC)

Current

(A Max.)

Power

(W)

MPM-05SV-03

0.125

0.080

3.3

1.25

4.0

7.5

4,000

72

MPM-05SV-05

0.125

0.080

5.0

1.00

5.0

7.5

4,000

77

MPM-05SV-09

0.125

0.080

9.0

0.55

5.0

12.0

1,800

79

MPM-05SV-12

0.125

0.080

12.0

0.42

5.0

20.0

1,800

81

MPM-05SV-15

0.125

0.080

15.0

0.33

5.0

20.0

1,500

82

MPM-05SV-24

0.125

0.080

24.0

0.23

5.0

30.0

330

84

Derating Curve

Typical Connection

1. It is recommended that an external fuse and NTC be used. The

recommended fuse is a 1.0A/300 VAC slow blow.

2. All units are rated for EN 55022 (CE/RE) class B without external

components.

3. All units are rated for EN 61000-4-4 (±2 kV) with the addition of

the MOV shown in the typical connection above. They will meet

EN 61000-4-4 (±4 kV) with the additional input components

shown in the typical connection diagram shown on page 3.

4. All units are rated for EN 61000-4-5 (±1 kV/±2 kV) with the addi-

tion of the MOV shown in the typical connection above. They will

Notes:

1. Operation at no load will not damage the units, however, they

may not meet all specifications.

2. Load regulation is measured for an output change of 10% to

100% at nominal input line.

3. When measuring output ripple, it is recommended that an

external 0.1 µF high frequency ceramic capacitor be placed

in parallel with a 47 µF high frequency electrolytic capacitor

4. The max lead temp for wave soldering is ±5% for a time

period of 5 to 10S. For hand soldering, it is ±10% for 3 to 5S.

Input Voltage Vs Load

The diagram above illustrates a typical application connection of the MPM-05SV series. Notes on this circuit (starting with the input circuit) are:

MPD offers a wide variety of input protection and

filtering modules for use with our AC & DC power

modules. The MACFM-02A may be used with

the MPM-05SV, as shown on page. Full data-

sheets for all our input modules are available on

our website, or call the factory for a more help.

5. All units are rated for EN 55022 (CE/RE) class B without

external components.

6. All units are rated for EN 61000-4-4 (±2 kV) with the addi-

tion of the MOV shown in the typical connection below. They

will meet EN 61000-4-4 (±4 kV) with the additional input

components shown in the typical connection diagram shown

on page 3.

7. All units are rated for EN 61000-4-5 (±1 kV/±2 kV) with the addi-

tion of the MOV shown in the typical connection below. They will

meet EN 61000-4-5 (±2 kV /±4 kV) with the input components

shown in the typical connection diagram on page 3.

8. It is recommended that a fuse be used on the input of a power

supply for protection. For the MPM-05SV-xx series, a

1.0A/300 VAC slow blow should be used.

meet EN 61000-4-5 (±2 kV /±4 kV) with the input components

shown in the typical connection diagram on page 3.

5. If output noise levels lower than the specified limits are required,

The recommended values are shown in the table at right. The

of capacitors should be 80% or above.

6. The TVS is added to protect circuits being powered from damage

if the module fails.

Model

TVS

MPM-05SV-03

1.0 µF/50V

330 µF/10V

SMBJ7.0A

MPM-05SV-05

1.0 µF/50V

330 µF/10V

SMBJ7.0A

MPM-05SV-09

1.0 µF/50V

120 µF/25V

SMBJ12A

MPM-05SV-12

1.0 µF/50V

120 µF/25V

SMBJ20A

MPM-05SV-15

1.0 µF/50V

68 µF/25V

SMBJ20A

MPM-05SV-24

1.0 µF/50V

68 µF/35V

SMBJ30A