PIC16F876ATISLASHML datasheet(181/234 Pages) MICROCHIP

181 / 234 page

 2003 Microchip Technology Inc.

DS39582B-page 179

PIC16F87XA

VOL

Output Low Voltage

D080

I/O ports

—

0.6

IOL = 8.5 mA, VDD = 4.5V,

-40

°C to +85°C

D083

OSC2/CLKO (RC osc config)

—

0.6

IOL = 1.6 mA, VDD = 4.5V,

-40

°C to +85°C

VOH

Output High Voltage

D090

I/O ports(3)

VDD – 0.7

—

IOH = -3.0 mA, VDD = 4.5V,

-40

°C to +85°C

D092

OSC2/CLKO (RC osc config)

VDD – 0.7

—

IOH = -1.3 mA, VDD = 4.5V,

-40

°C to +85°C

D150*

VOD

Open-Drain High Voltage

—

8.5

RA4 pin

Capacitive Loading Specs on

Output Pins

D100

COSC2

OSC2 pin

—

In XT, HS and LP modes when

external clock is used to drive

OSC1

D101

D102

CIO

All I/O pins and OSC2 (RC mode)

SCL, SDA (I2C mode)

—

400

Data EEPROM Memory

D120

Endurance

100K

—

E/W -40

°C to +85°C

D121

VDRW

VDD for read/write

VMIN

—

5.5

Using EECON to read/write,

VMIN = min. operating voltage

D122

TDEW

Erase/write cycle time

—

Program Flash Memory

D130

Endurance

10K

100K

—

E/W -40

°C to +85°C

D131

VPR

VDD for read

VMIN

—5.5

VMIN = min. operating voltage

D132A

VDD for erase/write

VMIN

—

5.5

Using EECON to read/write,

VMIN = min. operating voltage

D133

TPEW

Erase/Write cycle time

—

17.2

DC Characteristics: PIC16F873A/874A/876A/877A (Industrial, Extended)

PIC16LF873A/874A/876A/877A (Industrial) (Continued)

DC CHARACTERISTICS

Standard Operating Conditions (unless otherwise stated)

Operating temperature

-40°C

≤ TA ≤ +85°C for industrial

-40°C

≤ TA ≤ +125°C for extended

Operating voltage VDD range as described in DC specification

(Section 17.1)

Param

No.

Sym

Characteristic

Min

Typ†

Max

Units

Conditions

These parameters are characterized but not tested.

† Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance

only and are not tested.

Note 1:

In RC oscillator configuration, the OSC1/CLKI pin is a Schmitt Trigger input. It is not recommended that the

PIC16F87XA be driven with external clock in RC mode.

The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels

represent normal operating conditions. Higher leakage current may be measured at different input voltages.

Negative current is defined as current sourced by the pin.

PIC16F876ATI/ML Datasheet(PDF) 181 Page - Microchip Technology

PIC16F876ATI/ML Datasheet(HTML) 181 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL