Electronic Components Datasheet Search
  New Zealand  ▼
ALLDATASHEET.CO.NZ

X  

LM2619ATL/NOPB Datasheet(PDF) 7 Page - Texas Instruments

Part # LM2619ATL/NOPB
Description  500-mA Sub-Miniature Step-Down DC-DC Converter
PDF  21 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  TI1 [Texas Instruments]
Direct Link  http://www.ti.com
Logo TI1 - Texas Instruments

LM2619ATL/NOPB Datasheet(HTML) 7 Page - Texas Instruments

Back Button LM2619ATL/NOPB Datasheet HTML 3Page - Texas Instruments LM2619ATL/NOPB Datasheet HTML 4Page - Texas Instruments LM2619ATL/NOPB Datasheet HTML 5Page - Texas Instruments LM2619ATL/NOPB Datasheet HTML 6Page - Texas Instruments LM2619ATL/NOPB Datasheet HTML 7Page - Texas Instruments LM2619ATL/NOPB Datasheet HTML 8Page - Texas Instruments LM2619ATL/NOPB Datasheet HTML 9Page - Texas Instruments LM2619ATL/NOPB Datasheet HTML 10Page - Texas Instruments LM2619ATL/NOPB Datasheet HTML 11Page - Texas Instruments Next Button
Zoom Inzoom in Zoom Outzoom out
 7 / 21 page
background image
HIGHER EFFICIENCY
C1
10PF
C3*
0.1PF
VIN
3.9V to
5.5V
L1
10PH
D1**
C2
10PF
VOUT
3.6V
C5
10pF
C4
220pF
R3 68.1k
R1
46.4k
R2
33.2k
PWM/PFM
ON/OFF
SYSTEM
CONTROLLER
LM2619
*C3 IS OPTIONAL
**D1 IS OPTIONAL FOR
PVIN
SW
EAOUT
PGND
SGND
SYNC/MODE
EN
EANEG
FB
V DD
LM2619
www.ti.com
SNVS212B – NOVEMBER 2002 – REVISED MAY 2013
DEVICE INFORMATION
The LM2619 is a simple, step-down DC-DC converter optimized for powering circuits in mobile phones, portable
communicators, and similar battery powered RF devices. It is based on a current-mode buck architecture, with
synchronous rectification in PWM mode for high efficiency. It is designed for a maximum load capability of
500mA in PWM mode. Maximum load range may vary from this depending on input voltage, output voltage and
the inductor chosen.
The device has all three of the pin-selectable operating modes required for powering circuits in mobile phones
and other sophisticated portable devices with complex power management needs. Fixed-frequency PWM
operation offers full output current capability at high efficiency while minimizing interference with sensitive IF and
data acquisition circuits. During standby operation, hysteretic PFM mode reduces quiescent current to 160µA typ.
to maximize battery life. Shutdown mode turns the device off and reduces battery consumption to 0.02µA (typ).
DC PWM mode feedback voltage precision is ±1%. Efficiency is typically 96% for a 200mA load with 3.6V output,
3.9V input. The efficiency can be further increased by using a schottky diode like MBRM120L as shown in
Figure 20. PWM mode quiescent current is 600µA typ. The output voltage can be set from 1.5V to 3.6V by using
external feedback resistors.
Additional features include soft-start, current overload protection, over voltage protection and thermal shutdown
protection.
The LM2619 is constructed using a chip-scale 10-pin thin DSBGA package. This package offers the smallest
possible size, for space-critical applications such as cell phones, where board area is an important design
consideration. Use of a high switching frequency (600kHz) reduces the size of external components. Board area
required for implementation is only 0.58in2(375mm2).
Use of a DSBGA package requires special design considerations for implementation. (See DSBGA PACKAGE
ASSEMBLY AND USE in Application Information.) Its fine bump-pitch requires careful board design and
precision assembly equipment.
Figure 20. Typical Operating Circuit for 3.6V Output Voltage
CIRCUIT OPERATION
Referring to Figure 20, Figure 21, Figure 22, and Figure 23, the LM2619 operates as follows. During the first part
of each switching cycle, the control block in the LM2619 turns on the internal PFET switch. This allows current to
flow from the input through the inductor to the output filter capacitor and load. The inductor limits the current to a
ramp with a slope of (VIN–VOUT)/L, by storing energy in a magnetic field. During the second part of each cycle,
the controller turns the PFET switch off, blocking current flow from the input, and then turns the NFET
synchronous rectifier on. In response, the inductor's magnetic field collapses, generating a voltage that forces
current from ground through the synchronous rectifier to the output filter capacitor and load. As the stored energy
is transferred back into the circuit and depleted, the inductor current ramps down with a slope of VOUT/L. If the
inductor current reaches zero before the next cycle, the synchronous rectifier is turned off to prevent current
reversal. The output filter capacitor stores charge when the inductor current is high, and releases it when low,
smoothing the voltage across the load.
Copyright © 2002–2013, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: LM2619



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com