TMS570LS1114 datasheet(150/169 Pages) TI1

150 / 169 page

TMS570LS1114

SPNS188B – OCTOBER 2012 – REVISED FEBRUARY 2015

www.ti.com

7.11.5 SPI Slave Mode I/O Timings

Table 7-35. SPI Slave Mode External Timing Parameters (CLOCK PHASE = 0, SPICLK = input, SPISIMO =

input, and SPISOMI = output)(1)(2)(3)(4)

NO.

Parameter

MIN

MAX

Unit

tc(SPC)S

Cycle time, SPICLK(5)

2(6)

tw(SPCH)S

Pulse duration, SPICLK high (clock polarity = 0)

tw(SPCL)S

Pulse duration, SPICLK low (clock polarity = 1)

3(6)

tw(SPCL)S

Pulse duration, SPICLK low (clock polarity = 0)

tw(SPCH)S

Pulse duration, SPICLK high (clock polarity = 1)

4(6)

td(SPCH-SOMI)S

Delay time, SPISOMI valid after SPICLK high (clock

trf(SOMI) + 20

polarity = 0)

td(SPCL-SOMI)S

Delay time, SPISOMI valid after SPICLK low (clock polarity

trf(SOMI) + 20

= 1)

5(6)

th(SPCH-SOMI)S

Hold time, SPISOMI data valid after SPICLK high (clock

polarity =0)

th(SPCL-SOMI)S

Hold time, SPISOMI data valid after SPICLK low (clock

polarity =1)

6(6)

tsu(SIMO-SPCL)S

Setup time, SPISIMO before SPICLK low (clock polarity =

tsu(SIMO-SPCH)S

Setup time, SPISIMO before SPICLK high (clock polarity =

7(6)

th(SPCL-SIMO)S

Hold time, SPISIMO data valid after SPICLK low (clock

polarity = 0)

th(SPCH-SIMO)S

Hold time, SPISIMO data valid after S PICLK high (clock

polarity = 1)

td(SPCL-SENAH)S

Delay time, SPIENAn high after last SPICLK low (clock

1.5tc(VCLK)

2.5tc(VCLK)+tr(ENAn)+

polarity = 0)

td(SPCH-SENAH)S

Delay time, SPIENAn high after last SPICLK high (clock

1.5tc(VCLK)

2.5tc(VCLK)+ tr(ENAn) +

polarity = 1)

td(SCSL-SENAL)S

Delay time, SPIENAn low after SPICSn low (if new data

tf(ENAn)

tc(VCLK)+tf(ENAn)+27

has been written to the SPI buffer)

(1)

The MASTER bit (SPIGCR1.0) is cleared and the CLOCK PHASE bit (SPIFMTx.16) is cleared.

(2)

If the SPI is in slave mode, the following must be true: tc(SPC)S ≥ (PS + 1) tc(VCLK), where PS = prescale value set in SPIFMTx.[15:8].

(3)

For rise and fall timings, see Table 5-7.

(4)

tc(VCLK) = interface clock cycle time = 1 /f(VCLK)

(5)

When the SPI is in Slave mode, the following must be true:

For PS values from 1 to 255: tc(SPC)S ≥ (PS +1)tc(VCLK) ≥ 40ns, where PS is the prescale value set in the SPIFMTx.[15:8] register bits.

For PS values of 0: tc(SPC)S = 2tc(VCLK) ≥ 40ns.

(6)

The active edge of the SPICLK signal referenced is controlled by the CLOCK POLARITY bit (SPIFMTx.17).

150

Peripheral Information and Electrical Specifications

Submit Documentation Feedback

Product Folder Links: TMS570LS1114

TMS570LS1114 Datasheet(PDF) 150 Page - Texas Instruments

TMS570LS1114 Datasheet(HTML) 150 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL