| Electronic Components Datasheet Search |
|
MCP1624-I/MC Datasheet(PDF) 9 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
MCP1624-I/MC Datasheet(HTML) 9 Page - Microchip Technology |
|
9 / 30 page ![]() 2010-2016 Microchip Technology Inc. DS40001420D-page 9 MCP1623/24 3.0 PIN DESCRIPTIONS The descriptions of the pins are listed in Table 3-1. TABLE 3-1: PIN FUNCTION TABLE 3.1 Switch Node Pin (SW) Connects the inductor from the input voltage to the SW pin. The SW pin carries inductor current and can be as high as 425 mA peak. The integrated N-Channel switch drain and integrated P-Channel switch source are internally connected at the SW node. 3.2 Ground Pin (GND) The ground or return pin is used for circuit ground connection. Length of trace from input cap return, output cap return and GND pin should be made as short as possible to minimize noise on the GND pin. 3.3 Enable Pin (EN) The EN pin is a logic-level input used to enable or disable device switching and lower quiescent current while disabled. A logic high (greater than 90% of VIN) will enable the regulator output. A logic low (less than 20% of VIN) will ensure that the regulator is disabled. 3.4 Feedback Voltage Pin (FB) The FB pin is used to provide output voltage regulation by using a resistor divider. The FB voltage will be 1.21V typical with the output voltage in regulation. 3.5 Output Voltage Pin (VOUT) The output voltage pin connects the integrated P-Channel MOSFET to the output capacitor. The FB voltage divider is also connected to the VOUT pin for voltage regulation. 3.6 Power Supply Input Voltage Pin (VIN) Connects the input voltage source to VIN. The input source should be decoupled to GND with a 4.7 µF minimum capacitor. 3.7 Signal Ground Pin (SGND) The signal ground pin is used as a return for the integrated VREF and error amplifier. In the 2x3 DFN package, the SGND and power ground (PGND) pins are connected externally. 3.8 Power Ground Pin (PGND) The power ground pin is used as a return for the high--current N-Channel switch. In the 2x3 DFN package, the PGND and signal ground (SGND) pins are connected externally. 3.9 Output Voltage Sense Pin (VOUTS) The output voltage sense pin connects the regulated output voltage to the internal bias circuits. In the 2x3 DFN package, VOUTS and VOUTP are connected externally. 3.10 Output Voltage Power Pin (VOUTP) The output voltage power pin connects the output voltage to the switch node. High current flows through the integrated P-Channel and out of this pin to the output capacitor and output. In the 2x3 DFN package, VOUTS and VOUTP are connected externally. 3.11 Exposed Thermal Pad (EP) There is an internal electrical connection between the Exposed Thermal Pad (EP) and the VSS pin; they must be connected to the same potential on the Printed Circuit Board (PCB). MCP1623/24 Symbol Description SOT-23 2x3 DFN 1 5 SW Switch Node, Boost Inductor Input Pin 2 — GND Ground Pin 3 4 EN Enable Control Input Pin 4 1 FB Feedback Voltage Pin 5— VOUT Output Voltage Pin 68 VIN Input Voltage Pin —2 SGND Signal Ground Pin —3 PGND Power Ground Pin —7 VOUTS Output Voltage Sense Pin —6 VOUTP Output Voltage Power Pin — 9 EP Exposed Thermal Pad (EP); must be connected to VSS. |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |