LM6165JSLASH883 datasheet(4/12 Pages) NSC

4 / 12 page

DC Electrical Characteristics (Continued)

The following specifications apply for Supply Voltage = ±15V, V

CM = 0, RL ≥ 100 kΩ and RS = 50Ω unless otherwise noted.

Boldface limits apply for T

A = TJ = TMIN to TMAX; all other limits TA = TJ = 25˚C.

Symbol

Parameter

Conditions

Typ

LM6165

LM6265

LM6365

Units

Limit

(Notes 4, 12)

(Note 4)

Output Voltage

Supply = ±15V,

+14.2

+13.5

+13.4

Swing

L = 2kΩ

+13.3

Min

−13.4

−13.0

−12.9

−12.7

−12.8

Min

Supply = +5V

4.2

3.5

3.4

L = 2kΩ (Note 5)

3.3

Min

1.3

1.7

1.8

2.0

1.9

Max

Output Short

Source

Circuit Current

Min

Sink

Min

Supply Current

5.0

6.5

6.8

6.7

6.9

Max

AC Electrical Characteristics

The following specifications apply for Supply Voltage = ±15V, V

CM = 0, RL ≥ 100 kΩ and RS = 50Ω unless otherwise noted.

Boldface limits apply for T

A = TJ = TMIN to TMAX; all other limits TA = TJ = 25˚C. (Note 6)

Symbol

Parameter

Conditions

Typ

LM6165

LM6265

LM6365

Units

Limit

(Notes 4, 12)

(Note 4)

GBW

Gain Bandwidth

F = 20 MHz

725

575

500

MHz

Min

350

Product

Supply = ±5V

500

Slew Rate

V = +25 (Note 9)

300

200

V/µs

Min

180

Supply = ±5V

200

PBW

Power Bandwidth

OUT = 20 VPP

4.5

MHz

Product

Settling Time

10V Step to 0.1%

V = −25, RL = 2kΩ

Phase Margin

V = +25

Deg

Differential Gain

NTSC, A

V = +25

<0.1

Differential Phase

NTSC, A

V = +25

<0.1

Deg

np-p

Input Noise Voltage

F = 10 kHz

np-p

Input Noise Current

F = 10 kHz

1.5

Note 1: “Absolute Maximum Ratings” indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is

functional, but do not guarantee specific performance limits.

Note 2: Continuous short-circuit operation at elevated ambient temperature can result in exceeding the maximum allowed junction temperature of 150˚C.

Note 3: The typical junction-to-ambient thermal resistance of the molded plastic DIP (N) is 105˚C/Watt, and the molded plastic SO (M) package is 155˚C/Watt, and

the cerdip (J) package is 125˚C/Watt. All numbers apply for packages soldered directly into a printed circuit board.

Note 4: All limits guaranteed by testing or correlation.

Note 5: For single supply operation, the following conditions apply: V+ = 5V, V− = 0V, VCM = 2.5C, VOUT = 2.5V. Pin1&Pin8(VOS Adjust) are each connected

to Pin 4 (V−) to realize maximum output swing. This connection will degrade VOS.

Note 6: CL ≤ 5pF.

Note 7: In order to achieve optimum AC performance, the input stage was designed without protective clamps. Exeeding the maximum differential input voltage re-

sults in reverse breakdown of the base-emitter junction of one of the input transistors and probable degradation of the input parameters (especially VOS,IOS, and

Noise).

LM6165J/883 Datasheet(PDF) 4 Page - National Semiconductor (TI)

LM6165J/883 Datasheet(HTML) 4 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12

Datasheet Download

Link URL