HT32F1655 datasheet(12/48 Pages) HOLTEK

12 / 48 page

Rev. 1.00

1� of �8

�� 01�

3�-bit ARM® Cortex™-M3 MCU

HT3�F1656/HT3�F1655

Inter-integrated Circuit – I2C

▀ Supports both master and slave modes with a frequency of up to 1 MHz

▀ Provide an arbitration function and clock synchronisation

▀ Supports 7-bit and 10-bit addressing modes and general call addressing

▀ Supports slave multi-addressing mode with maskable address

The I2C Module is an internal circuit allowing communication with an external I2C interface which

is an industry standard two line serial interface used for connection to external hardware. These

two serial lines are known as a serial data line, SDA, and a serial clock line, SCL. The I2C module

provides three data transfer rates: 1. 100 kHz in the Standard mode, 2. 400 kHz in the Fast mode

and 3. 1 MHz in the Fast mode plus mode. The SCL period generation register is used to setup

different kinds of duty cycle implementations for the SCL pulse.

The SDA line which is connected directly to the I2C bus is a bi-directional data line between the

master and slave devices and is used for data transmission and reception. The I2C module also has

an arbitration detect function and clock synchronisation to prevent situations where more than one

master attempts to transmit data to the I2C bus at the same time.

Serial Peripheral Interface – SPI

▀ Supports both master and slave mode

▀ Frequency of up to 36 MHz for master mode and 24MHz for slave mode

▀ FIFO Depth: 8 levels

▀ Multi-master and multi-slave operation

The Serial Peripheral Interface, SPI, provides an SPI protocol data transmit and receive function

in both master and slave mode. The SPI interface uses 4 pins, which are the serial data input and

output lines MISO and MOSI, the clock line, SCK, and the slave select line, SEL. One SPI device

acts as a master device which controls the data flow using the SEL and SCK signals to indicate the

start of data communication and the data sampling rate. To receive a data byte, the streamed data

bits are latched on a specific clock edge and stored in the data register or in the RX FIFO. Data

transmission is carried out in a similar way but in a reverse sequence. The mode fault detection

provides a capability for multi-master applications.

Universal Synchronous Asynchronous Receiver Transmitter – USART

▀ Supports both asynchronous and clocked synchronous serial communication modes

▀ Asynchronous operating baud rate up to 4.5 MHz and synchronous operating rate up to 9 MHz

▀ Full duplex communication

▀ Fully programmable serial communication characteristics including:

● Word length: 7, 8, or 9-bit character

● Parity: Even, odd, or no-parity bit generation and detection

● Stop bit: 1 or 2 stop bit generation

● Bit order: LSB-first or MSB-first transfer

▀ Error detection: Parity, overrun, and frame error

▀ Auto hardware flow control mode - RTS, CTS

▀ IrDA SIR encoder and decoder

▀ RS485 mode with output enable control

▀ FIFO Depth: 16 x 9 bits for both receiver and transmitter

HT32F1655 Datasheet(PDF) 12 Page - Holtek Semiconductor Inc

HT32F1655 Datasheet(HTML) 12 Page - Holtek Semiconductor Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48

Datasheet Download

Link URL