Electronic Components Datasheet Search
  New Zealand  ▼
ALLDATASHEET.CO.NZ

X  

TLE4998C8D Datasheet(PDF) 18 Page - Infineon Technologies AG

Part # TLE4998C8D
Description  High Performance Programmable Single/Dual Linear Hall Sensor
PDF  27 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  INFINEON [Infineon Technologies AG]
Direct Link  http://www.infineon.com
Logo INFINEON - Infineon Technologies AG

TLE4998C8D Datasheet(HTML) 18 Page - Infineon Technologies AG

Back Button TLE4998C8D Datasheet HTML 14Page - Infineon Technologies AG TLE4998C8D Datasheet HTML 15Page - Infineon Technologies AG TLE4998C8D Datasheet HTML 16Page - Infineon Technologies AG TLE4998C8D Datasheet HTML 17Page - Infineon Technologies AG TLE4998C8D Datasheet HTML 18Page - Infineon Technologies AG TLE4998C8D Datasheet HTML 19Page - Infineon Technologies AG TLE4998C8D Datasheet HTML 20Page - Infineon Technologies AG TLE4998C8D Datasheet HTML 21Page - Infineon Technologies AG TLE4998C8D Datasheet HTML 22Page - Infineon Technologies AG Next Button
Zoom Inzoom in Zoom Outzoom out
 18 / 27 page
background image
TLE4998C8(D)
SPC Output
Data Sheet
18
Revision 1.1, 2017-01
7.4
SPC Modes
SPC enables the use of enhanced protocol functionality due to the ability to select between “synchronous”, “range
selection” and “ID selection” protocol mode. The ID register is only used in ID selection mode.
7.4.1
Synchronous Transmission
In the “synchronous” mode, the sensor (slave) starts to transfer a complete data frame only after a low pulse is
forced by the master on the OUT pin. This means that the data line is bidirectional - an open drain output of the
micro controller (master) sends the trigger pulse. The sensor then initiates a sync pulse and starts to calculate the
new output data value. After the synchronization period, the data follows in form of a standard SENT frame,
starting with the status, data and CRC nibbles. At the end, an end pulse allows the CRC nibble decoding and
indicates that the data line is idle again. The timing diagram in Figure 7-1 visualizes a synchronous transmission.
Figure 7-3
Bidirectional Communication in Synchronous Mode
7.4.2
Synchronous Transmission Including Range Selection
The low time duration of the master can be used to select the magnetic range of the sensor in SPC dynamic range
selection mode.
Table 7-5
SPC Mode Selection
Mode
Parameter Prot MSB
Parameter Prot LSB
Synchronous
0
No effect
Dynamic range selection
1
0
ID selection
1
1
Table 7-6
Master Pulse Timing for Synchronous Mode
Parameter
Symbol
Values
Unit
Note / Test Condition
Min.
Typ.
Max.
Master low time
t
mlow
1.5
2.75
4
UT1)
1) UT = Programmed nominal SPC unit time.
–
Table 7-7
Master Pulse Timing for Dynamic Range Mode
Parameter
Symbol
Values
Unit
Note / Test Condition
Min.
Typ.
Max.
Master low time
t
mlow
1.5
3.25
5
UT1)
1) UT = Programmed nominal SPC unit time.
Range = 200 mT (
R=0)
9
12
15
UT
Range = 100 mT (
R=1)
24
31.5
39
UT
Range = 50 mT (
R=3)
Sensor
CPU
VDD
OUT
GND
Capcom-Unit
Outpin (OD)



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27


Datasheet Download

Go To PDF Page


Link URL



Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Contact us   |   Privacy Policy   |   Link to Datasheet    |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com