FUSB307BVMPX datasheet(5/57 Pages) ONSEMI

5 / 57 page

FUSB307B

www.onsemi.com

Pin Descriptions

Table 2. PIN DESCRIPTION

Name

Type

Description

USB TYPE−C CONNECTOR INTERFACE

CC1

I/O

Type−C connector Configuration Channel (CC) pins. Initially used to determine

when an attach has occurred and what the orientation of the insertion is. Function-

ality after attach depends on mode of operation detected.

Operating as a host:

− Sets the allowable charging current for VBUS to be sensed by the attached

device

− Used to communicate with devices using USB BMC Power Delivery

− Used to detect when a detach has occurred

Operating as a device:

− Indicates what the allowable sink current is from the attached host

− Used to communicate with devices using USB BMC Power Delivery

CC2

I/O

GND

Ground

VBUS

Power

VBUS supply pin for attach and detach detection when operating as an upstream

facing port (Device)

POWER INTERFACE

VDD

Power

Input supply voltage

LDO

LDO Output

3.3 V LDO Output

VCONN

Power Switch

Regulated input to be switched to correct CC pin as VCONN to power USB3.1

fully featured cables, powered accessories or dongles bridging Type C to other

video or audio connectors

SIGNAL INTERFACE

SCL1/SDA2 (Note 1)

Open−Drain I/O

I2C serial clock/data signal to be connected to the I2C master

SDA1/SCL2 (Note 1)

Open−Drain I/O

I2C serial clock/data signal to be connected to the I2C master

INT_N

Open−Drain Output

Active LOW open drain interrupt output used to prompt the processor to read the

I2C register bits

ORIENT/I2C_

ADDR (Note 1)

3−State CMOS Output

Selects I2C Address on Power up and then becomes a General Purpose CMOS

Output

DBG_N

Open−Drain I/O

Debug Accessory Detection Open−Drain Output

GPIO2

3−State CMOS I/O

General Purpose I/O 2

GPIO1

3−State CMOS I/O

General Purpose I/O 1

VBUS SOURCE AND SINK INTERFACE

SNK

CMOS Output

Controls external VBUS Sink Load Switch on/off (Active High)

SRC

CMOS Output

Controls external VBUS Source Load Switch on/off (Active High)

1. A different I2C address is used depending on which SDA and SCL are used and the state of ORIENT/I2C_ADDR at power up.

Power Up, Initialization and Reset

When power is first applied to VDD or VBUS, the

FUSB307B goes through its POR sequence to load up all the

default values in the register map, read all the fuses so that

the trimmed values are available when VDD or VBUS is in

its valid range. A software reset can be executed by writing

SW_RES to 1 in RESET Register. This executes a full reset

of the FUSB307B similar to POR where all the I2C registers

go to their default state.

When powered down, the FUSB307B is configured as a

UFP with CC1 and CC2 have their respective Rd

pull−downs enabled such that a SOURCE can detect this as

a UFP and turn on VBUS.

For the FUSB307B device, power may become available

from VBUS when VDD is not present. This state is still

considered “Dead Battery” until VDD is present. During

Dead Battery, the FUSB307B will continue presenting Rd.

Once VDD is available, the TCPM can start the DRP

toggle by setting COMMAND.LOOK4CON on the

FUSB307B device.

FUSB307BVMPX Datasheet(PDF) 5 Page - ON Semiconductor

FUSB307BVMPX Datasheet(HTML) 5 Page - ON Semiconductor

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57

Datasheet Download

Link URL