| Electronic Components Datasheet Search |
|
68HC05JB4 Datasheet(PDF) 18 Page - Freescale Semiconductor, Inc |
|
|
|||||||||||||||||||||||||||||
68HC05JB4 Datasheet(HTML) 18 Page - Freescale Semiconductor, Inc |
|
18 / 134 page ![]() GENERAL RELEASE SPECIFICATION February 24, 1999 MOTOROLA GENERAL DESCRIPTION MC68HC05JB4 1-6 REV 2 1.4.3 RESET This is an I/O pin. This pin can be used as an input to reset the MCU to a known start-up state by pulling it to the low state. The RESET pin contains a steering diode to discharge any voltage on the pin to VDD, when the power is removed. An internal pull-up is also connected between this pin and VDD. The RESET pin con- tains an internal Schmitt trigger to improve its noise immunity as an input. This pin is an output pin if LVR triggers an internal reset. 1.4.4 IRQ (MASKABLE INTERRUPT REQUEST) This input pin drives the asynchronous IRQ interrupt function of the CPU. The IRQ interrupt function has a mask option to provide either only negative edge-sensitive triggering or both negative edge-sensitive and low level-sensitive triggering. If the option is selected to include level-sensitive triggering, the IRQ input requires an external resistor to VDD for "wired-OR" operation, if desired. The IRQ pin contains an internal Schmitt trigger as part of its input to improve noise immunity. NOTE Each of the PA0 thru PA3 I/O pins may be connected as an OR function with the IRQ interrupt function by a mask option. This capability allows keyboard scan applications where the transitions or levels on the I/O pins will behave the same as the IRQ pin. The edge or level sensitivity selected by a separate mask option for the IRQ pin also applies to the I/O pins OR’ed to create the IRQ signal. 1.4.5 V3.3 This is an output reference voltage nominally set at 3.3 volt DC. 1.4.6 D+ and D– These two lines carry the USB differential data. For low speed device such as MC68HC05JB4, a 1.5 k Ω resistor is required to be connected across D– and 3.3V for proper signal termination. 1.4.7 PA0-PA7 These eight I/O lines comprise Port-A. PA0 to PA7 are push-pull pins with internal pull-up resistors. The state of any pin is software programmable and all Port A lines are configured as inputs during power-on or reset. The internal pull-up resis- tor on PA0-4 is software enable. The PA0 thru PA3 can be connected via an inter- nal NAND gate to the IRQ interrupt function enabled by a mask option. PA5 thru PA7 has built in 10mA pull-down device for direct LED drive. In addition, PA6 and PA7 both have Slow Falling Edge Control which is enabled by software and can sink 25mA current selectable by mask option. PA0 thru PA4 have built-in schmitt triggered input. PA4 can be used as an extra interrupt pin (IRQ2) when IRQ2 inter- rupt is enabled. Freescale Semiconductor, Inc. For More Information On This Product, Go to: www.freescale.com |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |