WL40W1F-DAC4ASSLASHQ datasheet(2/7 Pages) MSYSTEM

2 / 7 page

MODEL: WL40W1F-DAC4A

WL40W1F SPECIFICATIONS

ES-9083 Rev.1 Page 2/7

http://www.m-system.co.jp/

Channels: 1 to 43ch

Security: 128bit AES

Indicator LEDs: 920Run, 920Link, 920ERR

Protocol: Modbus-RTU

Communication module: Coordinator module incorporated

(Oki Electric Industry Co., Ltd. )

Radio parameters setting: Configurator software

Antenna

•Sleeve antenna (Model: MH920-ANT-F (S))

Indoor use

Non-waterproof

Non-directional

Gain: 3.0dBi max.

•Rooftop antenna (Model: MH920-ANT-F (R))

Outdoor/indoor use

Cable length: 2.5 m

Waterproof performance: IPx6 (except connector)

Non-directional

Gain: 2.0dBi max.

INPUT SPECIFICATIONS

■CONTACT INPUT (NPN/PNP)

Number of input: 2 points

Rated input voltage:

24 V DC: ±10 %, ripple 5 %p-p max. (for power input 24 V

DC)

12 V DC: ±10 %, ripple 5 %p-p max. (for power input 12 V

DC)

ON voltage/ON Current:

≥ 16 V DC (between input terminal and COM)/ ≥ 3.7 mA

(for power input 24 V DC)

≥ 7.5 V DC (between input terminal and COM)/ ≥ 3.7 mA

(for power input 12 V DC)

OFF voltage/OFF current:

≤ 5 V DC (between input terminal and COM)/ ≥ 1 mA (for

power input 24 V DC)

≤ 3 V DC (between input terminal and COM)/ ≥ 1 mA (for

power input 12 V DC)

Input current:

≤ 5.5 mA (at 24 V DC) (for power input 24 V DC)

≤ 5.5 mA (at 12 V DC) (for power input 12 V DC)

Input resistance:

approx. 4.4 kΩ (for power input 24 V DC)

approx. 2.2 kΩ (for power input 12 V DC)

Read rate: ≤ 5 msec.

ON delay time: ≤ 2.0 msec.

OFF delay time: ≤ 2.0 msec.

Contact input status indicator LED: lights up when the

contact is ON (Dl1, Dl2).

OUTPUT SPECIFICATIONS

Output setting: Configurator software

■TRANSISTOR OUTPUT

Number of output: 2 points

Common: Negative common (NPN)

Rated load voltage:

24 V DC: ±10 %, ripple 5 %p-p max. (for power input 24 V

DC)

12 V DC: ±10 %, ripple 5 %p-p max. (for power input 12 V

DC)

Rated output current: 0.1 A

Residual voltage: ≤ 1.2 V

Leakage current: ≤ 0.1 mA

ON delay time: ≤ 2.0 msec.

OFF delay time: ≤ 2.0 msec.

Overload current protection function: Limits the current

value when overcurrent is detected.

Overheat protection function: Turns OFF the outputs when

overheat is detected. (When driving an inductive load,

connect a diode in parallel with the load.)

Transistor output status indicator LED: lights up when the

contact is ON (DO1, DO2).

INSTALLATION

Current consumption:

24 V DC: ≤ 70 mA (contact I/O load charge is not included)

12 V DC: ≤ 130mA (contact I/O load charge is not included)

Operating temperature: -10 to +55°C (14 to 131°F)

Storage temperature: -10 to +55°C (14 to +131°F)

Operating humidity: 10 to 90 %RH (non-condensing)

Atmosphere: No corrosive gas or heavy dust

Mounting: DIN rail

Weight

Unit: Approx. 260 g (0.57 lb)

Sleeve antenna (standard): 27 g (0.95 oz)

Rooftop antenna: 52 g (1.83 oz)

PERFORMANCE

Insulation resistance: ≥ 100 MΩ with 500 V DC

Dielectric strength: 1500 V AC @ 1 minute

(power input to FE1 to contact input to transistor output to

antenna connector)

STANDARDS & APPROVALS

Module conforming to FCC Part 15 incorporated

WL40W1F-DAC4AS/Q Datasheet(PDF) 2 Page - M-System Co.,Ltd.

WL40W1F-DAC4AS/Q Datasheet(HTML) 2 Page - M-System Co.,Ltd.

Html Pages

1 2 3 4 5 6 7

Datasheet Download

Link URL