| Electronic Components Datasheet Search |
|
TUSB6250 Datasheet(PDF) 72 Page - Texas Instruments |
|
|
|
|||||||||||||||||||||||||||||
TUSB6250 Datasheet(HTML) 72 Page - Texas Instruments |
|
72 / 124 page ![]() Miscellaneous and GPIO Configuration Registers 9−7 SLLS535A − January 2004 TUSB6250 9.7 PUPDSLCT_ATPOUT: Pullup and Pulldown Resistor Selection Register for ATA/ATAPI Outputs (XDATA at F08F) The PUPDSLCT_ATPOUT register allows the MCU to select the desired integrated pullup or pulldown resistors for the TUSB6250’s ATA/ATAPI output terminals. Normally, these resistors are not used in functional operation. However, they can be used to help achieve the low-power suspend budget for bus-powered applications. All pulldown resistors on the ATA/ATAPI bus are enabled as a power-up default, since the TUSB6250’s ATA/ATAPI output buffers are turned off during power up. The MCU must write to the PUPDPWDN_ATPOUT register to disable all the undesired pulldown resistors when it is ready to enable and drive the ATA/ATAPI bus. Each bit in the PUPDSLCT_ATPOUT register can be configured individually by the MCU by: • If the MCU sets any bit to 1, the pullup resistor is selected and the pulldown resistor is deselected. • If the MCU clears any bit to 0, the pulldown resistor is selected and the pullup resistor is deselected. The power-up default is the pulldown resistor enabled and the pullup resistor disabled for all the ATA/ATAPI output pins. 765 43210 RSV PUSLRSTATA PUSLDIOW PUSLDIOR PUSLDMACK PUSLDA PUSLCS1 PUSLCS0 R/O R/W R/W R/W R/W R/W R/W R/W BIT NAME RESET FUNCTION 0 PUSLCS0 0 CS0 pin pullup/pulldown resistor selection by the MCU. 1 PUSLCS1 0 CS1 pin pullup/pulldown resistor selection by the MCU. 2 PUSLDA 0 DA2, DA1, and DA0 pins pullup/pulldown resistor selection by the MCU. 3 PUSLDMACK 0 DMACK pin pullup/pulldown resistor selection by the MCU. 4 PUSLDIOR 0 DIOR pin pullup/pulldown resistor selection by the MCU. 5 PUSLDIOW 0 DIOW pin pullup/pulldown resistor selection by the MCU. 6 PUSLRSTATA 0 RST_ATA pin pullup/pulldown resistor selection by the MCU. Whenever the MCU sets the HARD_RST bit in the ATPIFCNFG1 register, this bit is cleared, which means the pulldown resistor is selected. 7 RSV 0 Reserved = 0 |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |