| Electronic Components Datasheet Search |
|
TUSB6250 Datasheet(PDF) 94 Page - Texas Instruments |
|
|
|
|||||||||||||||||||||||||||||
TUSB6250 Datasheet(HTML) 94 Page - Texas Instruments |
|
94 / 124 page ![]() ATA/ATAPI Interface Port 11−13 SLLS535A − January 2004 TUSB6250 Table 11−3 shows the register address map for the command and control block registers used in the ATA and ATAPI devices. Table 11−3. ATA and ATAPI Command and Control Block Registers ATP_ADR ATP_ADR ATA PROTOCOL ATAPI PROTOCOL ATP_ADR [3] ATP_ADR [2:0] READ WRITE READ WRITE CONTROL BLOCK REGISTER 0 (CS1 pin asserted) 6h Alternate status Device control Alternate status Device control COMMAND BLOCK REGISTER 0h Data register Data register 1h Error register Feature register Error register Feature register 2h Sector count Interrupt reason 1 3h Sector number 1 (CS0 pin asserted) 4h Cylinder low Byte count low (CS0 pin asserted) 5h Cylinder high Byte count high 6h Device/head Device select 7h Status Command Status Command NOTE: The other addressable spaces not listed in the table are either reserved, not used, or obsolete addresses according to the ATA/ATAPI-5 specification. It is the application firmware’s responsibility to ensure not to access those spaces. However, if developers have the need to implement some vendor-specific function in those spaces, the TUSB6250 hardware does not restrict such access and still allows the transfer to go through. 11.5.6 ATPACSREG3: ATA/ATAPI Access Register 3 (XDATA at F0D5) 765 43210 SECT_CNT7 SECT_CNT6 SECT_CNT5 SECT_CNT4 SECT_CNT3 SECT_CNT2 SECT_CNT1 SECT_CNT0 R/O R/O R/O R/O R/O R/O R/O R/O BIT NAME RESET FUNCTION 0 SECT_CNT [7:0] 00h Sector count [7:0] is the lower 8 bits of SEC_CNT [8:0], which contains the read-only sector count value utilized by the ATA PIO data transfer only. The SEC_CNT [8:0] initial value: S Comes from TRNS_BCN [17:9] when the MCU first loads the initial transfer byte count value. S Should be consistent with the meaning of the ATA sector count register in the ATA PIO mode. After transferring each sector data (512 bytes), SEC_CNT [8:0] is decremented by 1. If the command execution is terminated normally, the final value of sector count [8:0] should become 0. 11.5.7 TRANSBCNT0: USB or ATA/ATAPI Transfer Byte Count Register 0 (XDATA at F0D6) There are two physical sets of transfer byte count registers in the TUSB6250, which share the same address range from 0xF0D6 to 0xF0D9 hex. • The USB transfer byte count register 0−3, which is used to count the data transferred across the USB interface. • The ATA/ATAPI transfer byte count register 0−3, which is used to count the data transferred across the ATA/ATAPI interface. When the MCU performs write access to these registers (0xF0D6–0xF0D9), both the USB transfer byte count register 0−3 and the ATA/ATAPI transfer byte count register 0−3 are loaded with the same initial value. When the read access to either set of these registers is desired, the MCU has to set the UABYCNAB bit in the ATPIFCNFG0 register to select the read access to a particular register set. |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |