ADP322ACPZ-189-R7 datasheet(4/24 Pages) AD

4 / 24 page

ADP322/ADP323

Data Sheet

Rev. E | Page 4 of 24

Parameter

Symbol

Test Conditions/Comments

Min

Typ

Max

Unit

EN INPUT

EN Input Logic High

VIH

2.5 V ≤ VBIAS ≤ 5.5 V

1.2

EN Input Logic Low

VIL

2.5 V ≤ VBIAS ≤ 5.5 V

0.4

EN Input Leakage Current

VI-LEAKAGE

EN1 = EN2 = EN3 = VIN or GND

0.1

µA

EN1 = EN2 = EN3 = VIN or GND,

TJ = −40°C to +125°C

µA

UNDERVOLTAGE LOCKOUT

UVLO

Input Bias Voltage (VBIAS)

Rising

UVLORISE

2.45

Input Bias Voltage (VBIAS)

Falling

UVLOFALL

2.0

Hysteresis

UVLOHYS

180

OUTPUT NOISE

OUTNOISE

10 Hz to 100 kHz, VIN = 5 V, VOUT = 3.3 V

µV rms

10 Hz to 100 kHz, VIN = 5 V, VOUT = 2.8 V

µV rms

10 Hz to 100 kHz, VIN = 3.6 V, VOUT = 2.5 V

µV rms

10 Hz to 100 kHz, VIN = 3.6 V, VOUT = 1.2 V

µV rms

10 Hz to 100 kHz, VIN = 3.6 V, VOUT = 0.5 V

µV rms

POWER SUPPLY REJECTION RATIO

PSRR

VIN = 1.8 V, VOUT = 0.8 V, IOUT = 100 mA

100 Hz

1 kHz

10 kHz

100 kHz

1 MHz

VIN = 3.3 V, VOUT = 2.8 V, IOUT = 100 mA

100 Hz

1 kHz

10 kHz

100 kHz

1 MHz

Accuracy when VOUTx is connected directly to FBx. When the VOUTx voltage is set by external feedback resistors, the absolute accuracy in adjust mode depends on

the tolerances of the resistors used.

Based on an end point calculation using 1 mA and 200 mA loads.

The dropout voltage specification applies only to output voltages greater than 1.8 V. Dropout voltage is defined as the input to output voltage differential when the

input voltage is set to the nominal output voltage.

Start-up time is defined as the time between the rising edge of ENx to VOUTx being at 90% of its nominal value.

Current-limit threshold is defined as the current at which the output voltage drops to 90% of the specified typical value. For example, the current limit for a 3.0 V

output voltage is defined as the current that causes the output voltage to drop to 90% of 3.0 V, that is, 2.7 V.

INPUT AND OUTPUT CAPACITOR, RECOMMENDED SPECIFICATIONS

Table 2.

Parameter

Symbol

Test Conditions/Comments

Min

Typ

Max

Unit

MINIMUM INPUT AND OUTPUT CAPACITANCE1

CMIN

TA = −40°C to +125°C

0.70

µF

CAPACITOR ESR

RESR

TA = −40°C to +125°C

0.001

The minimum input and output capacitance must be greater than 0.70 µF over the full range of operating conditions. The full range of operating conditions in the

application must be considered during device selection to ensure that the minimum capacitance specification is met. X7R and X5R type capacitors are recommended;

Y5V and Z5U capacitors are not recommended for use with LDOs.

ADP322ACPZ-189-R7 Datasheet(PDF) 4 Page - Analog Devices

ADP322ACPZ-189-R7 Datasheet(HTML) 4 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

Datasheet Download

Link URL