Within SOA

0.75A

≥1.5A

High

Low

Positive

Negative

Source

Fault Sink

Enable Input Voltage

Enable Input Current

Current Limit Threshold

Cton Current

Efficiency

8

5040-1.9

5040-2.5

5040-3.3

5040-5.0

V

V

V

V

V

V

V

V

V

A

%

%/V

KHz

V

V

µA

µA

mA

mV

mV

µA

mA

%

%

%

%

Storage Temperature Range

Lead Temperature Range

(10 Seconds)

Case Operating Temperature

MSK5040 Series

MSK5040H/E Series

Junction Temperature

ABSOLUTE MAXIMUM RATINGS

-65°C to +150°C

300°C

-40°C to +85°C

-55°C to +125°C

+150°C

Input Voltage

Enable Voltage

Output Current

Sense Pin Voltage

Thermal Resistance

(Each MOSFET)

-0.3V, +36V

-0.3V, +36V

5.0 Amps

-0.3V, +7V

17°C/W

1,2,3

1

2,3

1

2,3

1

2,3

1

2,3

1

-

1,2,3

-

1,2,3

1,2,3

1

1

1

1

1

1

1

1

1

1

1

Input Supply Range

Output Current

Load Regulation

Line Regulation

Oscillator Frequency

Disabled Quiescent Current

-

1.9

-

2.5

-

3.3

-

5.0

-

4.5

1.5

0.06

300

-

-

0.5

0.2

2.0

100

-100

4.0

-

70

80

90

95

ELECTRICAL SPECIFICATIONS

4.75

1.88

1.8

2.47

2.38

3.27

3.14

4.95

4.75

4.0

-

-

270

2.0

-

-

-

-

80

-50

2.5

2.0

-

-

-

-

-

1.9

1.9

2.5

2.5

3.3

3.3

5.0

5.0

4.5

1.5

0.06

300

-

-

0.5

0.2

2.0

100

-100

4.0

-

70

80

90

95

30

1.92

2.0

2.53

2.63

3.33

3.47

5.05

5.25

-

-

0.10

330

-

0.5

2.0

2.0

2.5

120

-160

6.5

-

-

-

-

-

4.75

1.86

-

2.45

-

3.23

-

4.9

-

4.0

-

-

270

2.0

-

-

-

-

75

-45

2.5

2.0

-

-

-

-

30

1.94

-

2.55

-

3.37

-

5.1

-

-

-

0.15

330

-

0.5

2.0

2.0

2.5

125

-165

6.5

-

-

-

-

-

Group A

Subgroup

Min.

Typ.

Max.

Min.

Typ.

Max.

MSK 5040 SERIES

MSK 5040 H/E SERIES

Units

Test Conditions

Parameter

1

2

2

2

2

2

2

2

7

1

2

3

4

5

6

7

8

9

This parameter is guaranteed by design but need not be tested. Typical parameters are representative of actual device performance but are for reference only.

Industrial grade and 'E' suffix devices shall be tested to subgroup 1 unless otherwise specified.

Military grade devices ('H' suffix) shall be 100% tested to subgroups 1,2 and 3.

Subgroup 1

Subgroup 2

Subgroup 3

Actual switching frequency can be load dependent if output current is low. Refer to typical performance curves.

Alternate output voltages are available. Please contact the factory.

Continuous operation at or above absolute maximum ratings may adversely effect the device performance and/or life cycle.

NOTES:

Rev. F 2/06

2

8

2

8

8

Output Voltage 5040-1.9

Output Voltage 5040-2.5

Output Voltage 5040-3.3

Output Voltage 5040-5.0

9