| Electronic Components Datasheet Search |
|
CS48L32 Datasheet(PDF) 103 Page - Cirrus Logic |
|
|
|||||||||||||||||||||||||||||
CS48L32 Datasheet(HTML) 103 Page - Cirrus Logic |
|
103 / 192 page ![]() DS1219F4 Cirrus Logic 103 CS48L32 4.5 DSP Peripheral Control R1067024 (0x104810) SPI2_SPI_CONFIG1 27:24 SPI2_SS_IDLE_ DUR[3:0] 0x0 SPI2 slave select (SS) idle duration Minimum idle time between successive transactions, measured with respect to SCK cycle time. 0x0 = 0.5 cycles 0x1 = 0.5 cycles 0x2 = 1.0 cycle 0x3 = 1.5 cycles 0x4 = 2.0 cycles ... 0xF = 7.5 cycles 19:16 SPI2_SS_DELAY_ DUR[3:0] 0x0 SPI2 slave select (SS) delay duration Time between asserting SS and the first data bit, also the time between the last data bit and deasserting SS, each measured with respect to SCK cycle time. 0x0 = 0.5 cycles 0x1 = 0.5 cycles 0x2 = 1.0 cycle 0x3 = 1.5 cycles 0x4 = 2.0 cycles ... 0xF = 7.5 cycles 8 SPI2_3WIRE 0 SPI2 three-wire mode Configures the SIO0 data pin for bidirectional data input/output. Only valid if SPI2_SIO_WIDTH = 0. 0 = 4-wire Mode (SIO0 is MOSI, SIO1 is MISO) 1 = 3-wire Mode (SIO0 is bidirectional MOSI/MISO) 6 SPI2_DPHA 0 SPI2 data (SIOn) phase control 0 = RX data is valid 180 degrees (half SCK cycle) after TX data valid 1 = RX data is valid 360 degrees (full SCK cycle) after TX data valid 5 SPI2_CPHA 0 SPI2 clock (SCK) phase control 0 = TX data is valid on odd-numbered SCK edges (1, 3, 5, etc.) 1 = TX data is valid on even-numbered SCK edges (2, 4, 6, etc.) 4 SPI2_CPOL 0 SPI2 clock (SCK) polarity control 0 = SCK idle state is Logic 0 1 = SCK idle state is Logic 1 2:0 SPI2_SS_SEL[2:0] 000 SPI2 slave select (SS) control Selects the active SS pin. The active SS pin is asserted (Logic 0) at the start of the transaction and deasserted (Logic 1) at the end of the transaction. 000 = SPI2_SS1 001 = SPI2_SS2 010 = SPI2_SS3 011 = SPI2_SS4 All other codes are reserved. R1067028 (0x104814) SPI2_SPI_CONFIG2 0 SPI2_SS_FRC 0 SPI2 slave select (SS) force Forces the active SS pin to be asserted (Logic 0). 0 = Normal 1 = SS asserted (Logic 0) R1067044 (0x104824) SPI2_SPI_CONFIG3 16 SPI2_STALL_EN 0 SPI2 stall control 0 = Disabled 1 = Enabled This bit should be set at all times. Table 4-34. SPI2 Master Interface Control (Cont.) Register Address Bit Label Default Description |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |