ISL70417SEH

FN7962 Rev.5.00

Page 4 of 22

Oct 24, 2019

Absolute Maximum Ratings

Thermal Information

Maximum Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42V

Maximum Supply Voltage (LET = 73.9MeV•cm2/mg) . . . . . . . . . . . . . 40V

Maximum Differential Input Current . . . . . . . . . . . . . . . . . . . . . . . . . . 20mA

Maximum Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20V

Minimum/Maximum Input Voltage . . . . . . . . . . . . . . V- - 0.5V to V+ + 0.5V

Maximum/Minimum Input Current for Input Voltage >V+ or <V- . . . . ±20mA

Output Short-Circuit Duration (1 output at a time). . . . . . . . . . . . Indefinite

ESD Rating

Human Body Model (Tested per MIL-PRF-883 3015.7). . . . . . . . . . . 2kV

Machine Model (Tested per EIA/JESD22-A115-A) . . . . . . . . . . . . . . 300V

Charged Device Model (Tested per JESD22-C101D) . . . . . . . . . . . . . 2kV

Thermal Resistance (Typical)

θJA (°C/W) θJC (°C/W)

14 Ld Flatpack (Notes 5, 6). . . . . . . . . . . . .

105

15

Maximum Storage Temperature Range . . . . . . . . . . . . . .-65°C to +150°C

Maximum Junction Temperature (TJMAX) . . . . . . . . . . . . . . . . . . . . .+150°C

Recommended Operating Conditions

Ambient Operating Temperature Range . . . . . . . . . . . . . .-55°C to +125°C

Maximum Operating Junction Temperature . . . . . . . . . . . . . . . . . .+150°C

Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . 4.5V (±2.25V) to 30V (±15V)

CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions can adversely impact product

reliability and result in failures not covered by warranty.

NOTES:

5.

θJA is measured with the component mounted on a low effective thermal conductivity test board in free air. See TB379 for details.

6. For

θJC, the “case temp” location is the center of the ceramic on the package underside.

Electrical Specifications (VS ±15V) VCM = 0, VO = 0V, TA = +25°C, unless otherwise noted. Boldface limits apply across the

operating temperature range, -55°C to +125°C; over a total ionizing dose of 300krad(Si) with exposure at a high dose rate of 50 to 300krad(Si)/s; and

over a total ionizing dose of 50krad(Si) with exposure at a low dose rate of <10mrad(Si)/s.

PARAMETER

DESCRIPTION

TEST CONDITIONS

MIN

(Note 7)TYP

MAX

(Note 7)UNIT

VOS

Input Offset Voltage

10

85

µV

110

µV

TCVOS

Offset Voltage Drift

0.1

1

µV/°C

IB

Input Bias Current

-2.5

0.08

2.50

nA

TA = -55°C, +125°C

-5

5

nA

TA = +25°C, post radiation

-15

15

nA

TCIB

Input Bias Current Temperature Coefficient

-5

1

5

pA/°C

IOS

Input Offset Current

-2.50

0.08

2.50

nA

TA = -55°C, +125°C

-3

3

nA

TA = +25°C, post radiation

-6

6

nA

TCIOS

Input Offset Current Temperature

Coefficient

-3

0.42

3

pA/°C

VCM

Input Voltage Range

Guaranteed by CMRR test

-13

13

V

CMRR

Common-Mode Rejection Ratio

VCM = -13V to +13V

120

145

dB

120

dB

PSRR

Power Supply Rejection Ratio

VS = ±2.25V to ±20V

120

145

dB

120

dB

AVOL

Open-Loop Gain

VO = -13V to +13V, RL =10kΩ to ground

3,000

14,000

V/mV

VOH

Output Voltage High

RL = 10kΩ to ground

13.5

13.7

V

13.2

V

RL = 2kΩ to ground

13.30

13.55

V

13.0

V