| Electronic Components Datasheet Search |
|
AFEX8201 Datasheet(PDF) 35 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
AFEX8201 Datasheet(HTML) 35 Page - Texas Instruments |
|
35 / 95 page ![]() 7.3.2.8 ADC Bypass To test the offset, modify the ADC data path by programming the bypass data register, ADC_BYP.DATA (2Eh). This read/write register is used in two different ways. First, by setting the ADC_BYP.OFST_BYP_EN to 1, this bypass data register is used as a substitute for the ADC_OFFSET. However, if the ADC_BYP.DATA data must be stored in the ADC_OFFSET register, use the second method. Second, the ADC_BYP.DATA is used to set a known value into the ADC readback register of the channel being converted. Write the desired data into ADC_BYP.DATA, set the ADC_BYP.DATA_BYP_EN bit, and convert the selected channel. When ADC_BYP.DATA_BYP_EN bit is set to 1, the ADC conversion is bypassed, and the value of ADC_BYP.DATA is written into the selected ADC channel readback register. This setting is used to test the alarm settings of the ADC. When the ADC bypass is unused, set the ADC_BYP.DATA to 000h. Figure 7-11 shows the ADC bypass data flow. ADC_BYP.DATA Register 2Eh 0 1 0 1 ADC_OFFSET Register 28h ADC_AIN0 Register 24h ADC_AIN1 Register 25h ADC_TEMP Register 26h ADC_SD_MUX Register 27h + + ADC_BYP. OFST_BYP_EN Register 2Eh ADC_BYP. DATA_BYP_EN Register 2Eh ADC Data From ADC MUX ADC. ADC_OUT Register 2Dh ADC MUX 07FFh – OFFSET Stored as 2’s Complement CCS Pointer Read and Writeable for Testing Figure 7-11. ADC Bypass Data Flow 7.3.3 Programmable Out-of-Range Alarms The AFEx8201 are capable of continuously analyzing the supplies, external ADC inputs, DAC output voltage, reference, internal temperature, and other internal signals for normal operation. Normal operation for the conversion results is established through the lower- and upper-threshold registers. When any of the monitored inputs are out of the specified range, the corresponding alarm bit in the alarm status registers is set. The alarm bits in the alarm status registers are latched. The alarm bits are referred to as being latched because the alarm bits remain set until read by software. This design makes sure that out-of-limit events cannot be missed if the software is polling the device periodically. All bits are cleared when reading the alarm status registers, and all bits are reasserted if the out-of limit condition still exists on the next monitoring cycle. When the alarm event is cleared, the DAC is reloaded with the contents of the DAC active registers, which allows the DAC outputs to return to the previous operating point without any additional commands All alarms can be used to generate a hardware interrupt signal on the ALARM pin; see also Section 7.3.3.1. In addition, Section 7.3.3.2 describes how the alarm action can be individually configured for each alarm. www.ti.com AFE78201, AFE88201 SLASF44 – MAY 2023 Copyright © 2023 Texas Instruments Incorporated Submit Document Feedback 35 Product Folder Links: AFE78201 AFE88201 |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |