COM20051ILJP datasheet(21/74 Pages) SMSC

21 / 74 page

SMSC DS – COM20051I

Page 21

Rev. 03/27/2000

Since the Backplane Configuration encodes data differently than the traditional Hybrid Configuration, nodes utilizing

the Backplane Configuration cannot communicate directly with nodes utilizing the Traditional Hybrid Configuration.

The Backplane Configuration does not isolate the node from the media nor protect it from Common Mode noise, but

Common Mode Noise is less of a problem in short distances.

The COM20051I supplies a programmable output driver for Backplane Mode operation. A push/pull or open drain

driver can be selected by programming the P1MODE bit of the Setup Register (see register descriptions for details.)

The COM20051I defaults to an open drain output.

The Backplane Configuration provides for direct connection between the COM20051I and the physical medium in

open drain configuration of the output driver. Only one pull-up resistor (for open drain only) is required somewhere

on the media (not on each individual node). The nPULSE1 signal, in this mode, is an open drain or push/pull driver

and is used to directly drive the media. It issues a 200nS negative pulse to transmit a logic "1". Note that when used

in the open-drain mode, the COM20051I does not have a fail/safe input on the RXIN pin.

The nPULSE1 signal actually contains a weak pull-up resistor. This pull-up should not take the place of the resistor

required on the media for open drain mode. In typical applications, the serial backplane is terminated at both ends

and a bias is provided by the external pull-up resistor.

The RXIN signal is directly connected to the cable via an internal Schmitt trigger. A negative pulse on this input

indicates a logic "1". Lack of pulse indicates a logic "0". For typical single-ended backplane applications, RXIN is

connected to nPULSE1 to make the serial backplane data line. A ground line (from the coax or twisted pair) should

run in parallel with the signal. For applications requiring different treatment of the receive signal (like filtering or

squelching), nPULSE1 and RXIN remain as independent pins. External differential drivers/receivers for increased

range and common mode noise rejection, for example, would require the signals to be independent of one another.

When the device is in Backplane Mode, the clock provided by the nPULSE2 signal may be used for encoding the

data into a different encoding scheme or other synchronous operations needed on the serial data stream.

Differential Driver Configuration

The Differential Driver Configuration is a special case of the Backplane Mode. It is a DC coupled configuration

recommended for applications like car-area networks (CAN) or other cost-sensitive applications which do not require

direct compatibility with existing ARCNET nodes and do not require isolation. Figure 7 illustrates this configuration.

The Differential Driver Configuration cannot communicate directly with nodes utilizing the Traditional Hybrid

Configuration. Like the Backplane Configuration, the Differential Driver Configuration does not isolate the node from

the physical medium.

The Differential Driver interface includes a RS485 Driver/Receiver to transfer the data between the cable and the

COM20051I. The nPULSE1 signal transmits the data, provided the nTXEN signal is active. The nPULSE1 signal

issues a 200nS negative pulse to transmit a logic "1". The RXIN pin receives the data. A negative pulse on this

input indicates a logic "1". Lack of pulse indicates a logic "0". The transmitter portion of the COM20051I is disabled

during reset and the nPULSE1, nPULSE2 and nTXEN pins are inactive.

Table 2 - Typical Media

CABLE TYPE

NOMINAL

IMPEDANCE

ATTENUATION PER 1000 FT.

AT 5MHZ

RG-62 Belden #86262

5.5dB

RG-59/U Belden #89108

7.0dB

RG-11/U Belden #89108

5.5dB

IBM Type 1* Belden #89688

150

7.0dB

IBM Type 3* Telephone Twisted Pair Belden #1155A

100

17.9dB

COMCODE 26 AWG Twisted Pair Part #105-064-703 105

16.0dB

*Non-plenum-rated cables of this type are also available.

Note: For more detailed information on Cabling options including RS-485, transformer-coupled RS-485 and Fiber

Optic interfaces, please refer to TN7-5 - Cabling Guidelines for the COM20020 ULANC, available from Standard

Microsystems Corporation.

COM20051ILJP Datasheet(PDF) 21 Page - SMSC Corporation

COM20051ILJP Datasheet(HTML) 21 Page - SMSC Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74

Datasheet Download

Link URL