COM20051ILJP datasheet(39/74 Pages) SMSC

39 / 74 page

SMSC DS – COM20051I

Page 39

Rev. 03/27/2000

Transmit Command Chaining

When the microcontroller issues the first "Enable Transmit to Page fnn" command, the ARCNET core responds in the

usual manner by resetting the TA and TMA bits to prepare for the transmission from the specified page. The TA bit

can be used to see if there is currently a transmission pending, but the TA bit is really meant to be used in the non-

chaining mode only. The TTA bits provide the relevant information for the device in the Command Chaining mode.

In the Command Chaining Mode, at any time after the first command is issued, the processor can issue a second

"Enable Transmit from Page fnn" command. The ARCNET core stores the fact that the second transmit command

was issued, along with the page number.

After the first transmission is completed, the ARCNET core updates the Status Register by setting the TTA bit, which

generates an interrupt. The interrupt service routine should read the Status Register. At this point, the TTA bit will be

found to be a logic "1" and the TMA (Transmit Message Acknowledge) bit will tell the processor whether the

transmission was successful. After reading the Status Register, the "Clear Transmit Interrupt" command is issued,

FIGURE 12 – COMMAND CHAINING STATUS REGISTER QUEUE

thus resetting the TTA bit and clearing the interrupt.

Note that only the "Clear Transmit Interrupt" command will

clear the TTA bit and the interrupt. It is not necessary, however, to clear the bit or the interrupt right away because

the status of the transmit operation is double buffered in order to retain the results of the first transmission for analysis

by the processor. This information will remain in the Status Register until the "Clear Transmit Interrupt" command is

issued. Note that the interrupt will remain active until the command is issued, and the second interrupt will not occur

until the first interrupt is acknowledged. The ARCNET core guarantees a minimum of 200nS interrupt inactive time

interval between interrupts. The TMA bit is also double buffered to reflect whether the appropriate transmission was

a success. The TMA bit should only be considered valid after the corresponding TTA bit has been set to a logic "1".

The TMA bit never causes an interrupt.

When the token is received again, the second transmission will be automatically initiated after the first is completed

by using the stored "Enable Transmit from Page fnn" command. The operation is as if a new "Enable Transmit from

Page fnn" command has just been issued. After the first Transmit status bits are cleared, the Status Register will

again be updated with the results of the second transmission and a second interrupt resulting from the second

transmission will occur. The ARCNET core guarantees a minimum of 200ns interrupt inactive time interval before the

following edge.

The Transmitter Available (TA) bit of the Interrupt Mask Register now masks only the TTA bit of the Status Register,

not the TA bit as in the non-chaining mode. Since the TTA bit is only set upon transmission of a packet (not by

RESET), and since the TTA bit may easily be reset by issuing a "Clear Transmit Interrupt" command, there is no

need to use the TA bit of the Interrupt Mask Register to mask interrupts generated by the TTA bit of the Status

permits canceling a packet destined for a node not ready to receive.

If both packets should be canceled, two

"Disable Transmitter" commands should be issued.

Receive Command Chaining

Like the Transmit Command Chaining operation, the processor can issue two consecutive "Enable Receive from

Page fnn" commands.

After the first packet is received into the first specified page, the TRI bit of the Status Register will be set to logic "1",

causing an interrupt. Again, the interrupt need not be serviced immediately. Typically, the interrupt service routine

TRI

R I

P O R

TE S T

RE C O N

TMA

T TA

TMA

T TA

TR I

MS B

LS B

COM20051ILJP Datasheet(PDF) 39 Page - SMSC Corporation

COM20051ILJP Datasheet(HTML) 39 Page - SMSC Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74

Datasheet Download

Link URL