PIC18F258-ESLASHLSQTP datasheet(238/402 Pages) MICROCHIP

238 / 402 page

PIC18FXX8

DS41159E-page 236

FIGURE 19-9:

SHORTENING A BIT PERIOD (SUBTRACTING SJW FROM PHASE SEGMENT 2)

19.9

Programming Time Segments

Some requirements for programming of the time

segments:

• Prop Seg + Phase Seg 1

≥ Phase Seg 2

• Phase Seg 2

≥ Sync Jump Width

For example, assume that a 125 kHz CAN baud rate is

desired using 20 MHz for FOSC. With a TOSC of 50 ns,

a baud rate prescaler value of 04h gives a TQ of 500 ns.

To obtain a nominal bit rate of 125 kHz, the nominal bit

time must be 8

μs or 16 TQ.

Using 1 TQ for the Sync Segment, 2 TQ for the Propa-

gation Segment and 7 TQ for Phase Segment 1 would

place the sample point at 10 TQ after the transition.

This leaves 6 TQ for Phase Segment 2.

By the rules above, the Sync Jump Width could be the

maximum of 4 TQ. However, normally a large SJW is

only necessary when the clock generation of the differ-

ent nodes is inaccurate or unstable, such as using

ceramic resonators. Typically, an SJW of 1 is enough.

19.10 Oscillator Tolerance

As a rule of thumb, the bit timing requirements allow

ceramic resonators to be used in applications with

transmission rates of up to 125 Kbit/sec. For the full bus

speed range of the CAN protocol, a quartz oscillator is

required. A maximum node-to-node oscillator variation

of 1.7% is allowed.

19.11 Bit Timing Configuration

Registers

The Configuration registers (BRGCON1, BRGCON2,

BRGCON3) control the bit timing for the CAN bus

interface. These registers can only be modified when

the PIC18FXX8 is in Configuration mode.

19.11.1

BRGCON1

The BRP bits control the baud rate prescaler. The

SJW<1:0> bits select the synchronization jump width in

terms of multiples of TQ.

19.11.2

BRGCON2

The PRSEG bits set the length of the Propagation Seg-

ment in terms of TQ. The SEG1PH bits set the length of

Phase Segment 1 in TQ. The SAM bit controls how

many times the RXCAN pin is sampled. Setting this bit

to a ‘1’ causes the bus to be sampled three times; twice

at TQ/2 before the sample point and once at the normal

sample point (which is at the end of Phase Segment 1).

The value of the bus is determined to be the value read

during at least two of the samples. If the SAM bit is set

to a ‘0’, then the RXCAN pin is sampled only once at

the sample point. The SEG2PHTS bit controls how the

length of Phase Segment 2 is determined. If this bit is

set to a ‘1’, then the length of Phase Segment 2 is

determined by the SEG2PH bits of BRGCON3. If the

SEG2PHTS bit is set to a ‘0’, then the length of Phase

Segment 2 is the greater of Phase Segment 1 and the

information processing time (which is fixed at 2 TQ for

the PIC18FXX8).

19.11.3

BRGCON3

The PHSEG2<2:0> bits set the length (in TQ) of Phase

Segment 2 if the SEG2PHTS bit is set to a ‘1’. If the

SEG2PHTS bit is set to a ‘0’, then the PHSEG2<2:0>

bits have no effect.

Sync

Prop

Segment

Phase

Segment 1

Phase

Segment 2

≤ SJW

Sample Point

Nominal Bit Length

Actual Bit Length

PIC18F258-E/LSQTP Datasheet(PDF) 238 Page - Microchip Technology

PIC18F258-E/LSQTP Datasheet(HTML) 238 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL