TMS320DM6431 datasheet(81/225 Pages) TI

81 / 225 page

www.ti.com

3.7.1

Pin Muxing Selection At Reset

3.7.2

Pin Muxing Selection After Reset

TMS320DM6431

Digital Media Processor

SPRS342A – NOVEMBER 2006 – REVISED MARCH 2007

This section summarizes pin mux selection at reset.

The configuration pins AEM[2:0] and AEAW[2:0] latched at device reset determine default pin muxing for

the following Pin Mux Blocks:

• EMIFA/VPSS Block: default pin mux determined by AEM[2:0] and AEAW[2:0]. After reset, software

may modify settings in the PINMUX0 register to add VPFE functionalities into this block.

–

AEM[2:0] = 000b, AEAW[2:0] = don't care: Major Config Option A is selected. This block defaults to

61 GPIO pins.

–

AEM[2:0] = 001b, AEAW[2:0] = 000b to 100b: Major Config Option B is selected. This block

defaults to 8-bit EMIFA (Async) Pinout Mode 1, plus 24-to-32 GPIO pins.

–

AEM[2:0] = 101b, AEAW[2:0] = don't care: Major Config Option E is selected. This block defaults to

8-bit EMIFA (NAND) Pinout mode 5, plus 47 GPIO pins.

For a description of the PINMUX0 and PINMUX1 registers and more details on pin muxing, see

Section 3.7.2, Pin Muxing Selection After Reset.

The PINMUX0 and PINMUX1 registers in the System Module allow software to select the pin functions in

the Pin Mux Blocks. The pin control of some of the Pin Mux Blocks requires a combination of

PINMUX0/PINMUX1 bit fields. For more details on the combination of the PINMUX bit fields that control

each muxed pin, see Section 3.7.3.1, Multiplexed Pins on DM6431.

This section only provides an overview of the PINMUX0 and PINMUX1 registers. For more detailed

discussion on how to program each Pin Mux Block, see Section 3.7.3, Pin Multiplexing Details.

3.7.2.1 PINMUX0 Register Description

The Pin Multiplexing 0 Register (PINMUX0) controls the pin function in the EMIFA/VPSS Block. The

PINMUX0 register format is shown in Figure 3-11 and the bit field descriptions are given in Table 3-18.

Some muxed pins are controlled by more than one PINMUX bit field. For the combination of the PINMUX

bit fields that control each muxed pin, see Section 3.7.3.1, Multiplexed Pins on DM6431. For more

information on EMIFA/VPSS Block pin muxing, see Section 3.7.3.11, EMIFA/VPSS Block Muxing. For the

pin-by-pin muxing control of the EMIFA/VPSS Block, see Section 3.7.3.11.7, EMIFA/VPSS Block

Pin-By-Pin Multiplexing Summary.

CWEN

RSV

CI10SEL

RESERVED

CFLDSEL

HVDSEL

RSV

CCDCSEL

RSV

AEAW

SEL

R/W-0

R/W-00 000

R/W-0

R/W-LLL

RESERVED

CS3SEL

CS4SEL

CS5SEL

RESERVED

AEM

R/W-0000

R/W-00

R/W-000

R/W-LLL

LEGEND: R/W = Read/Write; R = Read only; L = pin state latched at reset rising edge; -n = value after reset

(1) For proper DM6431 device operation, always write a value of "0" to all RESERVED/RSV bits.

Figure 3-11. PINMUX0 Register (1)

Submit Documentation Feedback

Device Configurations

TMS320DM6431 Datasheet(PDF) 81 Page - Texas Instruments

TMS320DM6431 Datasheet(HTML) 81 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Download

Link URL