| Electronic Components Datasheet Search |
|
LM5045MHX/NOPB.A Datasheet(PDF) 27 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
LM5045MHX/NOPB.A Datasheet(HTML) 27 Page - Texas Instruments |
|
27 / 47 page ![]() UVLO LM5045 1.25V 20 2A SHUTDOWN VPWR R1 R2 STANDBY 0.4V R2 = 1.25V x R1 VPWR -1.25V + (20 2A x R1) VHYS 20 2A R1 = R2 = 1.25V x R1 VPWR-OFF -1.25V - (20 2A x R1) R1 = VHYS 20 2A LM5045 www.ti.com SNVS699H – FEBRUARY 2011 – REVISED JANUARY 2015 8.2.2.3 UVLO and OVP Voltage Divider Selection Two dedicated comparators connected to the UVLO and OVP pins are used to detect undervoltage and overvoltage conditions. The threshold values of both these comparators are set at 1.25 V. The two functions can be programmed independently with two separate voltage dividers from VIN to AGND as shown in Figure 22 and Figure 23, or with a three-resistor divider as shown in Figure 24. Independent UVLO and OVP pins provide greater flexibility for the user to select the operational voltage range of the system. When the UVLO pin voltage is below 0.4 V, the controller is in a low current shutdown mode. For a UVLO pin voltage greater than 0.4 V but less than 1.25 V the controller is in standby mode. Once the UVLO pin voltage is greater than 1.25 V, the controller is fully enabled. Two external resistors can be used to program the minimum operational voltage for the power converter as shown in Figure 22. When the UVLO pin voltage falls below the 1.25 V threshold, an internal 20 µA current sink is enabled to lower the voltage at the UVLO pin, thus providing threshold hysteresis. Resistance values for R1 and R2 can be determined from the following equations: where • VPWR is the desired turnon voltage • VHYS is the desired UVLO hysteresis at VPWR (6) For example, if the LM5045 is to be enabled when VPWR reaches 33 V, and disabled when VPWR is decreased to 31 V, R1 should be 100 kΩ, and R2 should be 4.2 kΩ. The voltage at the UVLO pin should not exceed 7 V at any time. Two external resistors can be used to program the maximum operational voltage for the power converter as shown in Figure 23. When the OVP pin voltage rises above the 1.25 V threshold, an internal 20-µA current source is enabled to raise the voltage at the OVP pin, thus providing threshold hysteresis. Resistance values for R1 and R2 can be determined from the following equations: (7) If the LM5045 is to be disabled when VPWR-OFF reaches 80 V and enabled when it is decreased to 78 V. R1 should be 100 k Ω, and R2 should be 1.5 kΩ. The voltage at the OVP pin should not exceed 7 V at any time. Figure 22. Basic UVLO Configuration Copyright © 2011–2015, Texas Instruments Incorporated Submit Documentation Feedback 27 Product Folder Links: LM5045 |
|
Link URL |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Contact us | Privacy Policy | Link to Datasheet | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |